rtc_register_device() is a managed interface but it doesn't use devres
by itself - instead it marks an rtc_device as "registered" and the devres
callback for devm_rtc_allocate_device() takes care of resource release.
This doesn't correspond with the design behind devres where managed
structures should not be aware of being managed. The correct solution
here is to register a separate devres callback for unregistering the
device.
While at it: rename rtc_register_device() to devm_rtc_register_device()
and add it to the list of managed interfaces in devres.rst. This way we
can avoid any potential confusion of driver developers who may expect
there to exist a corresponding unregister function.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201109163409.24301-8-brgl@bgdev.pl
The ds1307 charger infrastructure now allows to add a rx8130 charger
setup that..
- does not depend on trickle-resistor-ohms
- does not use DS13XX_TRICKLE_CHARGER_MAGIC trickle-charge select (TCS)
bits
- keeps previous no-charge behavior for device trees without
aux-voltage-chargeable
Make that happen.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-9-bst@pengutronix.de
Some RTC's batteries and supercaps were charged by default until now.
In contrast other RTCs allow charging but the driver did not configure
them to do so until now. These must not be charged by default to stay
backwards compatible.
In order to do that, store the charge default per chip.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-7-bst@pengutronix.de
DS13XX_TRICKLE_CHARGER_MAGIC sets the trickle-charge select (TCS) bits
(7..4). The datasheet of Maxim Integrated's DS1339 [1] for instance
reads:
"To prevent accidental enabling, only a pattern on 1010 enables the
trickle charger. All other patterns disable the trickle charger."
Since not all RTCs connected to a backup battery or supercap use these
bits DS13XX_TRICKLE_CHARGER_MAGIC should not get applied for all charger
setups unconditionally.
Epson's RX8130 is such an example: Instead of TCS bits "SMPTSEL1",
"SMPTSEL0", "CHGEN" and "INIEN" are expected as bit 7..4.
DS1339 and DS1340 are currently the only RTCs in the ds1307 driver that
apply DS13XX_TRICKLE_CHARGER_MAGIC to their setup register value. So
apply DS13XX_TRICKLE_CHARGER_MAGIC in do_trickle_setup_ds1339() which
is used by both RTCs.
[1] https://datasheets.maximintegrated.com/en/ds/DS1339-DS1339U.pdf
[2] https://support.epson.biz/td/api/doc_check.php?dl=app_RX8130CE
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-5-bst@pengutronix.de
Pull RTC updates from Alexandre Belloni:
"A quiet cycle this time.
- ds1307: properly handle oscillator failure flags
- imx-sc: alarm support
- pcf2123: alarm support, correct offset handling
- sun6i: add R40 support
- simplify getting the adapter of an i2c client"
* tag 'rtc-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (37 commits)
rtc: wm831x: Add IRQF_ONESHOT flag
rtc: stm32: remove one condition check in stm32_rtc_set_alarm()
rtc: pcf2123: Fix build error
rtc: interface: Change type of 'count' from int to u64
rtc: pcf8563: Clear event flags and disable interrupts before requesting irq
rtc: pcf8563: Fix interrupt trigger method
rtc: pcf2123: fix negative offset rounding
rtc: pcf2123: add alarm support
rtc: pcf2123: use %ptR
rtc: pcf2123: port to regmap
rtc: pcf2123: remove sysfs register view
rtc: rx8025: simplify getting the adapter of a client
rtc: rx8010: simplify getting the adapter of a client
rtc: rv8803: simplify getting the adapter of a client
rtc: m41t80: simplify getting the adapter of a client
rtc: fm3130: simplify getting the adapter of a client
rtc: tegra: Drop MODULE_ALIAS
rtc: sun6i: Add R40 compatible
dt-bindings: rtc: sun6i: Add the R40 RTC compatible
dt-bindings: rtc: Convert Allwinner A31 RTC to a schema
...
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop enabling the oscillator and removing the oscillator failure flags in
probe. Instead, return -EINVAL in .read_time when the oscillaotr is not
start or when it failed at some point. The oscillator gets enabled on the
first .set_time after failure and the failure flags are cleared.
This also removes the possibility of an infinite loop at probe where a
failing RTC will make the goto read_rtc to be taken every time.
Tested on mcp79411.
Reported-by: Mastro Gippo <gipmad@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When the EXTENSION.WADA bit is set, register 0x19 contains a bitmap of
week days, not a day of month. As Linux only handles a single alarm
without repetition using day of month is more flexible, so clear this
bit. (Otherwise a value depending on time.tm_wday would have to be
written to register 0x19.)
Also optimize setting the AIE bit to use a single register write instead
of a bulk write of three registers.
Fixes: ee0981be77 ("rtc: ds1307: Add support for Epson RX8130CE")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When voltage dropped since the RTC was last set the reported time is not
reliable. In this case return an error indicator instead of a bogus
time.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
While rx8130 has a register offset of 0x10 in its chip_desc, this isn't
used when regmap accesses are done. So add 0x10 to access the right
locations.
Fixes: ee0981be77 ("rtc: ds1307: Add support for Epson RX8130CE")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There used to be 16 declarations for static functions. By just adding a
declaration for the chips array and reordering the functions the 16
function declarations can be dropped.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Register frequency test using rtc_add_group to avoid a possible race
condition and simplify the code.
This also moves the attribute to its proper location under the rtc device
instead of the i2c parent device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On m41txx you can enable open-drain OUT pin to check if offset is ok.
Enabling OUT pin with frequency_test_enable attribute, OUT pin will tick
512 times faster than 1s tick base.
Enable or Disable FT bit on CONTROL register if freq_test is 1 or 0.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
m41txx chips can hold a calibration value to get correct clock bias.
Add offset handling (ranging between -63ppm and 126ppm) via sysfs.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
We don't have to define an extra config symbol, IS_REACHABLE does
what we need. And having this config symbol just to save the few
bytes of hwmon support on non-DS3231 chips isn't worth it IMO
(especially as the symbol is set per default).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The m41t11 variant is very similar to the already supported m41t00 and
m41t0, but it has also 56 bytes of NVRAM.
Add it to driver taking into account NVRAM section.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
data field points to m41t00, instead it should point to m41t0.
Driver works correctly because on both cases(m41t0 and m41t00) chip_desc
are equal.
Point to right enum m41t0 instead of m41t00.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it just before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Avoid allocating memory for struct nvmem_config as it is only necessary at
the nvmem registration.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call rtc_nvmem_register instead of letting the core do it and stop using
the nvmem_config member of struct rtc_device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The current code for checking and fixing the weekday in ds1307_probe
faces some issues:
- This check is applied to all chips even if its applicable (AFAIK)
to mcp794xx only
- The check uses MCP794XX constants for registers and bits even though
it's executed also on other chips (ok, this could be fixed easily)
- It relies on tm_wday being properly populated when core calls set_time
and set_alarm. This is not guaranteed at all.
First two issue we could solve by moving the check to the
mcp794xx-specific initialization (where also VBATEN flag is set).
The proposed alternative is in the set_alarm path for mcp794xx only and
calculates the alarm weekday based on the current weekday in the RTC
timekeeping regs and the difference between alarm date and current date.
So we are fine with any weekday even if it doesn't match the date.
Still there are cases where this could fail, e.g.:
- rtc date/time + weekday have power-on-reset default values
- alarm is set to actual date/time + x
- set_time is called (may change diff between rtc weekday and actual
weekday)
But similar issues we have with the current code too:
- rtc date/time + weekday have power-on-reset default values
- alarm is set to rtc date/time + x
- set_time is called before the alarm triggers
Using random rtc date/time with relative alarms simply can interfere
with set_time. I'm not totally convinced of either option yet.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Alignment should always match open parenthesis.
Also remove two unnecessary blank lines
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use sizeof where possible to ensure we don't read/write more than the
allocated buffer.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ds1307->regs is never used before being read or initialized locally. There
is no point in keeping a copy in memory.
Also limit the size of the read buffer to what is really used, rename buf
to regs for consistency and use sizeof() where possible.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This adds support for reading and writing date/time from/to ds1341 chip.
ds1341 chip has other features - alarms, input clock (can be used instead
of intercal oscillator for better accuracy), output clock ("square wave
generation"). However, not all of that is available at the same time.
Same chip pins, CLKIN/nINTA and SQW/nINTB, can be used either for
input/output clocks, or for alarm interrupts. Role of these pins on
particular board depends on hardware wiring.
We can add device tree properties that describe if each of pins is wired
as clock, or as interrupt, or left unconnected, and enable support for
corresponding functionality based on that. But that is cumbersome, requires
hardware for testing, and has to deal with bit enabling/disabling output
clock also affects which pins alarm interrupts are routed to.
Another factor is that there are hardware setups (i.e. ZII RDU2) that
power DS1341 from SuperCap, which makes power saving critical. For such
setups, kernel driver should leave register bits that control mentioned
pins in the state configured by bootloader.
Given all that, it was decided to limit support to "only date/time" for
now. That is enough for common use case. Full (and cumbersome)
implementation can be added later if ever needed.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove member nvram_offset from struct ds1307 and use the value stored
in struct chip_desc directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
