The tegra_smmu_probe_device() handles only the first IOMMU device-tree
phandle, skipping the rest. Devices like 3D module on Tegra30 have
multiple IOMMU phandles, one for each h/w block, and thus, only one
IOMMU phandle is added to fwspec for the 3D module, breaking GPU.
Previously this problem was masked by tegra_smmu_attach_dev() which
didn't use the fwspec, but parsed the DT by itself. The previous commit
to tegra-smmu driver partially reverted changes that caused problems for
T124 and now we have tegra_smmu_attach_dev() that uses the fwspec and
the old-buggy variant of tegra_smmu_probe_device() which skips secondary
IOMMUs.
Make tegra_smmu_probe_device() not to skip the secondary IOMMUs. This
fixes a partially attached IOMMU of the 3D module on Tegra30 and now GPU
works properly once again.
Fixes: 765a9d1d02 ("iommu/tegra-smmu: Fix mc errors on tegra124-nyan")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20210312155439.18477-1-digetx@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Removing 2 instances of alignment warnings
drivers/staging/vt6655/rxtx.h:153:1: warning: alignment 1 of ‘struct vnt_cts’ is less than 2 [-Wpacked-not-aligned]
drivers/staging/vt6655/rxtx.h:163:1: warning: alignment 1 of ‘struct vnt_cts_fb’ is less than 2 [-Wpacked-not-aligned]
The root cause seems to be that _because_ struct ieee80211_cts is marked as __aligned(2),
this requires any encapsulating struct to also have an alignment of 2.
Fixes: 2faf12c57e ("staging: vt665x: fix alignment constraints")
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Edmundo Carmona Antoranz <eantoranz@gmail.com>
Link: https://lore.kernel.org/r/20210316181736.2553318-1-eantoranz@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When data digest is enabled we should unmap pdu iovec before handling
the data digest pdu.
Signed-off-by: Elad Grupi <elad.grupi@dell.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
From the base spec, Figure 78:
"Controller Configuration, these fields are defined as parameters to
configure an "I/O Controller (IOC)" and not to configure a "Discovery
Controller (DC).
...
If the controller does not support I/O queues, then this field shall
be read-only with a value of 0h
Just perform this check for I/O controllers.
Fixes: a07b4970f4 ("nvmet: add a generic NVMe target")
Reported-by: Belanger, Martin <Martin.Belanger@dell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We only setup io queues for nvme controllers, and it makes absolutely no
sense to allow a controller (re)connect without any I/O queues. If we
happen to fail setting the queue count for any reason, we should not allow
this to be a successful reconnect as I/O has no chance in going through.
Instead just fail and schedule another reconnect.
Reported-by: Chao Leng <lengchao@huawei.com>
Fixes: 7110230719 ("nvme-rdma: add a NVMe over Fabrics RDMA host driver")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chao Leng <lengchao@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We only setup io queues for nvme controllers, and it makes absolutely no
sense to allow a controller (re)connect without any I/O queues. If we
happen to fail setting the queue count for any reason, we should not
allow this to be a successful reconnect as I/O has no chance in going
through. Instead just fail and schedule another reconnect.
Fixes: 3f2304f8c6 ("nvme-tcp: add NVMe over TCP host driver")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For our pure advisory use-case, we only rely on this call as a hint, so
fix the warning complaints of using the smp_processor_id variants with
preemption enabled.
Fixes: db5ad6b7f8 ("nvme-tcp: try to send request in queue_rq context")
Fixes: ada8317721 ("nvme-tcp: Fix warning with CONFIG_DEBUG_PREEMPT")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When the controller sends us a 0-length r2t PDU we should not attempt to
try to set up a h2cdata PDU but rather conclude that this is a buggy
controller (forward progress is not possible) and simply fail it
immediately.
Fixes: 3f2304f8c6 ("nvme-tcp: add NVMe over TCP host driver")
Reported-by: Belanger, Martin <Martin.Belanger@dell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
To avoid an error recovery deadlock where the keep alive work is waiting
for a request and thus can't be flushed to make progress for tearing down
the controller. Also print the error code returned from
blk_mq_alloc_request to help debugging any future issues in this code.
Based on an earlier patch from Hannes Reinecke <hare@suse.de>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Merge nvme_keep_alive into its only caller to prepare for additional
changes to this code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Fabrics drivers currently reserve two tags on the admin queue. But
given that the connect command is only run on a freshly created queue
or after all commands have been force aborted we only need to reserve
a single tag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
In the situations where the DWC3 gadget stops active transfers, once
calling the dwc3_gadget_giveback(), there is a chance where a function
driver can queue a new USB request in between the time where the dwc3
lock has been released and re-aquired. This occurs after we've already
issued an ENDXFER command. When the stop active transfers continues
to remove USB requests from all dep lists, the newly added request will
also be removed, while controller still has an active TRB for it.
This can lead to the controller accessing an unmapped memory address.
Fix this by ensuring parameters to prevent EP queuing are set before
calling the stop active transfers API.
Fixes: ae7e86108b ("usb: dwc3: Stop active transfers before halting the controller")
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1615507142-23097-1-git-send-email-wcheng@codeaurora.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the unused "u32 vdo[3]" part in the tps6598x_rx_identity_reg
struct. This helps avoid "failed to register partner" errors which
happen when tps6598x_read_partner_identity() fails because the
amount of data read is 12 bytes smaller than the struct size.
Note that vdo[3] is already in usb_pd_identity and hence
shouldn't be added to tps6598x_rx_identity_reg as well.
Fixes: f6c56ca91b ("usb: typec: Add the Product Type VDOs to struct usb_pd_identity")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Elias Rudberg <mail@eliasrudberg.se>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210311124710.6563-1-mail@eliasrudberg.se
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matthias reports that the Amazon Kindle automatically removes its
emulated media if it doesn't receive another SCSI command within about
one second after a SYNCHRONIZE CACHE. It does so even when the host
has sent a PREVENT MEDIUM REMOVAL command. The reason for this
behavior isn't clear, although it's not hard to make some guesses.
At any rate, the results can be unexpected for anyone who tries to
access the Kindle in an unusual fashion, and in theory they can lead
to data loss (for example, if one file is closed and synchronized
while other files are still in the middle of being written).
To avoid such problems, this patch creates a new usb-storage quirks
flag telling the driver always to issue a REQUEST SENSE following a
SYNCHRONIZE CACHE command, and adds an unusual_devs entry for the
Kindle with the flag set. This is sufficient to prevent the Kindle
from doing its automatic unload, without interfering with proper
operation.
Another possible way to deal with this would be to increase the
frequency of TEST UNIT READY polling that the kernel normally carries
out for removable-media storage devices. However that would increase
the overall load on the system and it is not as reliable, because the
user can override the polling interval. Changing the driver's
behavior is safer and has minimal overhead.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210317190654.GA497856@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When gadget is disconnected, running sequence is like this.
. composite_disconnect
. Call trace:
usb_string_copy+0xd0/0x128
gadget_config_name_configuration_store+0x4
gadget_config_name_attr_store+0x40/0x50
configfs_write_file+0x198/0x1f4
vfs_write+0x100/0x220
SyS_write+0x58/0xa8
. configfs_composite_unbind
. configfs_composite_bind
In configfs_composite_bind, it has
"cn->strings.s = cn->configuration;"
When usb_string_copy is invoked. it would
allocate memory, copy input string, release previous pointed memory space,
and use new allocated memory.
When gadget is connected, host sends down request to get information.
Call trace:
usb_gadget_get_string+0xec/0x168
lookup_string+0x64/0x98
composite_setup+0xa34/0x1ee8
If gadget is disconnected and connected quickly, in the failed case,
cn->configuration memory has been released by usb_string_copy kfree but
configfs_composite_bind hasn't been run in time to assign new allocated
"cn->configuration" pointer to "cn->strings.s".
When "strlen(s->s) of usb_gadget_get_string is being executed, the dangling
memory is accessed, "BUG: KASAN: use-after-free" error occurs.
Cc: stable@vger.kernel.org
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/1615444961-13376-1-git-send-email-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MODULE_SUPPORTED_DEVICE was added in pre-git era and never was
implemented. We can safely remove it, because the kernel has grown
to have many more reliable mechanisms to determine if device is
supported or not.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MIPS fix from Thomas Bogendoerfer:
"Fix for fdt alignment when image is compressed"
* tag 'mips-fixes_5.12_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: vmlinux.lds.S: Fix appended dtb not properly aligned
Pull thermal framework fix from Daniel Lezcano:
"Fix NULL pointer access when the cooling device transition stats
table failed to allocate due to a big number of states (Manaf
Meethalavalappu Pallikunhi)"
* tag 'thermal-v5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal/core: Add NULL pointer check before using cooling device stats
SAMPLE_OA parameter enables sampling of OA buffer and results in a call
to init the OA buffer which initializes the OA unit head/tail pointers.
The OA_EXPONENT parameter controls the periodicity of the OA reports in
the OA buffer and results in starting a hrtimer.
Before gen12, all use cases required the use of the OA buffer and i915
enforced this setting when vetting out the parameters passed. In these
platforms the hrtimer was enabled if OA_EXPONENT was passed. This worked
fine since it was implied that SAMPLE_OA is always passed.
With gen12, this changed. Users can use perf without enabling the OA
buffer as in OAR use cases. While an OAR use case should ideally not
start the hrtimer, we see that passing an OA_EXPONENT parameter will
start the hrtimer even though SAMPLE_OA is not specified. This results
in an uninitialized OA buffer, so the head/tail pointers used to track
the buffer are zero.
This itself does not fail, but if we ran a use-case that SAMPLED the OA
buffer previously, then the OA_TAIL register is still pointing to an old
value. When the timer callback runs, it ends up calculating a
wrong/large number of available reports. Since we do a spinlock_irq_save
and start processing a large number of reports, NMI watchdog fires and
causes a crash.
Start the timer only if SAMPLE_OA is specified.
v2:
- Drop SAMPLE OA check when appending samples (Ashutosh)
- Prevent read if OA buffer is not being sampled
Fixes: 00a7f0d715 ("drm/i915/tgl: Add perf support on TGL")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210305210947.58751-1-umesh.nerlige.ramappa@intel.com
(cherry picked from commit be0bdd67fd)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On HSW/BDW with VT-d active the first tile row scanned out
after the first async flip of the frame often ends up corrupted.
Whether the corruption happens or not depends on the scanline
on which the async flip happens, but the behaviour seems very
consistent. Ie. the same set of scanlines (which are most scanlines)
always show the corruption. And another set of scanlines (far less
of them) never shows the corruption.
I discovered that disabling the fetch-stride stretching
feature cures the corruption. This is some kind of TLB related
prefetch thing AFAIK. We already disable it on SNB primary
planes due to a documented workaround. The hardware folks
indicated that disabling this should be fine, so let's go
with that.
And while we're here, let's document the relevant bits on all
pre-skl platforms.
Fixes: 2a636e240c ("drm/i915: Implement async flip for ivb/hsw")
Fixes: cda195f13a ("drm/i915: Implement async flips for bdw")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210220103303.3448-1-ville.syrjala@linux.intel.com
Reviewed-by: Karthik B S <karthik.b.s@intel.com>
(cherry picked from commit b7a7053ab2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In ww_acquire_init(), mutex_acquire() is gated by CONFIG_DEBUG_LOCK_ALLOC.
The dep_map in the ww_acquire_ctx structure is also gated by the
same config. However mutex_release() in ww_acquire_fini() is gated by
CONFIG_DEBUG_MUTEXES. It is possible to set CONFIG_DEBUG_MUTEXES without
setting CONFIG_DEBUG_LOCK_ALLOC though it is an unlikely configuration.
That may cause a compilation error as dep_map isn't defined in this
case. Fix this potential problem by enclosing mutex_release() inside
CONFIG_DEBUG_LOCK_ALLOC.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210316153119.13802-3-longman@redhat.com
The use_ww_ctx flag is passed to mutex_optimistic_spin(), but the
function doesn't use it. The frequent use of the (use_ww_ctx && ww_ctx)
combination is repetitive.
In fact, ww_ctx should not be used at all if !use_ww_ctx. Simplify
ww_mutex code by dropping use_ww_ctx from mutex_optimistic_spin() an
clear ww_ctx if !use_ww_ctx. In this way, we can replace (use_ww_ctx &&
ww_ctx) by just (ww_ctx).
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Link: https://lore.kernel.org/r/20210316153119.13802-2-longman@redhat.com
There is a possible chance that some cooling device stats buffer
allocation fails due to very high cooling device max state value.
Later cooling device update sysfs can try to access stats data
for the same cooling device. It will lead to NULL pointer
dereference issue.
Add a NULL pointer check before accessing thermal cooling device
stats data. It fixes the following bug
[ 26.812833] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
[ 27.122960] Call trace:
[ 27.122963] do_raw_spin_lock+0x18/0xe8
[ 27.122966] _raw_spin_lock+0x24/0x30
[ 27.128157] thermal_cooling_device_stats_update+0x24/0x98
[ 27.128162] cur_state_store+0x88/0xb8
[ 27.128166] dev_attr_store+0x40/0x58
[ 27.128169] sysfs_kf_write+0x50/0x68
[ 27.133358] kernfs_fop_write+0x12c/0x1c8
[ 27.133362] __vfs_write+0x54/0x160
[ 27.152297] vfs_write+0xcc/0x188
[ 27.157132] ksys_write+0x78/0x108
[ 27.162050] ksys_write+0xf8/0x108
[ 27.166968] __arm_smccc_hvc+0x158/0x4b0
[ 27.166973] __arm_smccc_hvc+0x9c/0x4b0
[ 27.186005] el0_svc+0x8/0xc
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1607367181-24589-1-git-send-email-manafm@codeaurora.org
As per UEFI spec 2.8B section 8.2, EFI_UNSUPPORTED may be returned by
EFI variable runtime services if no variable storage is supported by
firmware. In this case, there is no point for kernel to continue
efivars initialization. That said, efivar_init() should fail by
returning an error code, so that efivarfs will not be mounted on
/sys/firmware/efi/efivars at all. Otherwise, user space like efibootmgr
will be confused by the EFIVARFS_MAGIC seen there, while EFI variable
calls cannot be made successfully.
Cc: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
When KVM_REQ_MASTERCLOCK_UPDATE request is issued (e.g. after migration)
we need to make sure no vCPU sees stale values in PV clock structures and
thus all vCPUs are kicked with KVM_REQ_CLOCK_UPDATE. Hyper-V TSC page
clocksource is global and kvm_guest_time_update() only updates in on vCPU0
but this is not entirely correct: nothing blocks some other vCPU from
entering the guest before we finish the update on CPU0 and it can read
stale values from the page.
Invalidate TSC page in kvm_gen_update_masterclock() to switch all vCPUs
to using MSR based clocksource (HV_X64_MSR_TIME_REF_COUNT).
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210316143736.964151-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
HV_X64_MSR_TSC_EMULATION_STATUS indicates whether TSC accesses are emulated
after migration (to accommodate for a different host TSC frequency when TSC
scaling is not supported; we don't implement this in KVM). Guest can use
the same MSR to stop TSC access emulation by writing zero. Writing anything
else is forbidden.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210316143736.964151-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are two issues for RV32,
1) if use FLATMEM, it is useless to enable SPARSEMEM_STATIC.
2) if use SPARSMEM, both SPARSEMEM_VMEMMAP and SPARSEMEM_STATIC is enabled.
Fixes: d95f1a542c ("RISC-V: Implement sparsemem")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
init_resources() allocates an array of resources, based on the current
total number of memory regions and reserved memory regions. However,
allocating this array using memblock_alloc() might increase the number
of reserved memory regions. If that happens, populating the array later
based on the new number of regions will cause out-of-bounds writes
beyond the end of the allocated array.
Fix this by allocating one more entry, which may or may not be used.
Fixes: 797f0375dd ("RISC-V: Do not allocate memblock while iterating reserved memblocks")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
When CONFIG_SOC_CANAAN is selected, the K210 sysctl driver is always
compiled. Since this driver early init function calls the function
k210_clk_early_init() implemented by the K210 clk driver, this driver
must also always be selected for compilation ot avoid build failures.
Avoid such build failures by always selecting CONFIG_COMMON_CLK and
CONFIG_COMMON_CLK_K210 when CONFIG_SOC_CANAAN is enabled.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Fixes: c6ca7616f7 ("clk: Add RISC-V Canaan Kendryte K210 clock driver")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
mpt3sas_get_port_by_id() can be called when a spinlock is held. Use
GFP_ATOMIC instead of GFP_KERNEL when allocating memory.
Issue spotted by call_kern.cocci:
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 7125 inside lock on line 7123 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 6842 inside lock on line 6839 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 6854 inside lock on line 6851 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 7706 inside lock on line 7702 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 10260 inside lock on line 10256 but uses GFP_KERNEL
Link: https://lore.kernel.org/r/20210220093951.905362-1-christophe.jaillet@wanadoo.fr
Fixes: 324c122fc0 ("scsi: mpt3sas: Add module parameter multipath_on_hba")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Both add_slot_store() and remove_slot_store() try to fix up the
drc_name copied from the store buffer by placing a NUL terminator at
nbyte + 1 or in place of a '\n' if present. However, the static buffer
that we copy the drc_name data into is not zeroed and can contain
anything past the n-th byte.
This is problematic if a '\n' byte appears in that buffer after nbytes
and the string copied into the store buffer was not NUL terminated to
start with as the strchr() search for a '\n' byte will mark this
incorrectly as the end of the drc_name string resulting in a drc_name
string that contains garbage data after the n-th byte.
Additionally it will cause us to overwrite that '\n' byte on the stack
with NUL, potentially corrupting data on the stack.
The following debugging shows an example of the drmgr utility writing
"PHB 4543" to the add_slot sysfs attribute, but add_slot_store()
logging a corrupted string value.
drmgr: drmgr: -c phb -a -s PHB 4543 -d 1
add_slot_store: drc_name = PHB 4543°|<82>!, rc = -19
Fix this by using strscpy() instead of memcpy() to ensure the string
is NUL terminated when copied into the static drc_name buffer.
Further, since the string is now NUL terminated the code only needs to
change '\n' to '\0' when present.
Cc: stable@vger.kernel.org
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
[mpe: Reformat change log and add mention of possible stack corruption]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210315214821.452959-1-tyreld@linux.ibm.com
In zonefs_open_zone(), if opened zone count is larger than
.s_max_open_zones threshold, we missed to recover .i_wr_refcnt,
fix this.
Fixes: b5c00e9757 ("zonefs: open/close zone on file open/close")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Commit 6654111c89 ("MIPS: vmlinux.lds.S: align raw appended dtb to 8
bytes") changed the alignment from STRUCT_ALIGNMENT bytes to 8 bytes.
The commit's message makes it sound like it was actually done on
purpose, but this is not the case. The commit was written when raw
appended dtb were not aligned at all. The STRUCT_ALIGN() was added a few
days before, in commit 7a05293af3 ("MIPS: boot/compressed: Copy DTB to
aligned address"). The true purpose of the commit was not to align
specifically to 8 bytes, but to make sure that the generated vmlinux'
size was properly padded to the alignment required for DTBs.
While the switch to 8-byte alignment worked for vmlinux-appended dtb
blobs, it broke vmlinuz-appended dtb blobs, as the decompress routine
moves the blob to a STRUCT_ALIGNMENT aligned address.
Fix this by changing the raw appended dtb blob alignment from 8 bytes
back to STRUCT_ALIGNMENT bytes in vmlinux.lds.S.
Fixes: 6654111c89 ("MIPS: vmlinux.lds.S: align raw appended dtb to 8 bytes")
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
