When using the driver in I2S TDM mode, the _fsl_ssi_set_dai_fmt()
function rewrites the number of slots previously set by the
fsl_ssi_set_dai_tdm_slot() function to 2 by default.
To fix this, let's use the saved slot count value or, if TDM
is not used and the slot count is not set, proceed as before.
Fixes: 4f14f5c11d ("ASoC: fsl_ssi: Fix number of words per frame for I2S-slave mode")
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20210216114221.26635-1-shc_work@mail.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
For mono channel, SSI will switch to Normal mode.
In Normal mode and Network mode, the Word Length Control bits
control the word length divider in clock generator, which is
different with I2S Master mode (the word length is fixed to
32bit), it should be the value of params_width(hw_params).
The condition "slots == 2" is not good for I2S Master mode,
because for Network mode and Normal mode, the slots can also
be 2. Then we need to use (ssi->i2s_net & SSI_SCR_I2S_MODE_MASK)
to check if it is I2S Master mode.
So we refine the formula for mono channel, otherwise there
will be sound issue for S24_LE.
Fixes: b0a7043d5c ("ASoC: fsl_ssi: Caculate bit clock rate using slot number and width")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/034eff1435ff6ce300b6c781130cefd9db22ab9a.1592276147.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The test case is
arecord -Dhw:0 -d 10 -f S16_LE -r 48000 -c 2 temp.wav &
aplay -Dhw:0 -d 30 -f S16_LE -r 48000 -c 2 test.wav
There will be error after end of arecord:
aplay: pcm_write:2051: write error: Input/output error
Capture and Playback work in parallel in master mode, one
substream stops, the other substream is impacted, the
reason is that clock is disabled wrongly.
The clock's reference count is not increased when second
substream starts, the hw_param() function returns in the
beginning because first substream is enabled, then in end
of first substream, the hw_free() disables the clock.
This patch is to move the clock enablement to the place
before checking of the device enablement in hw_param().
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1567012817-12625-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-50-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the sisr and sisr2 variable types to u32 to avoid the following
sparse warnings:
sound/soc/fsl/fsl_ssi.c:391:42: warning: incorrect type in argument 3 (different base types)
sound/soc/fsl/fsl_ssi.c:391:42: expected unsigned int *val
sound/soc/fsl/fsl_ssi.c:391:42: got restricted __be32 *<noident>
sound/soc/fsl/fsl_ssi.c:393:17: warning: restricted __be32 degrades to integer
sound/soc/fsl/fsl_ssi.c:393:15: warning: incorrect type in assignment (different base types)
sound/soc/fsl/fsl_ssi.c:393:15: expected restricted __be32 [usertype] sisr2
sound/soc/fsl/fsl_ssi.c:393:15: got unsigned int
sound/soc/fsl/fsl_ssi.c:396:50: warning: incorrect type in argument 3 (different base types)
sound/soc/fsl/fsl_ssi.c:396:50: expected unsigned int [unsigned] val
sound/soc/fsl/fsl_ssi.c:396:50: got restricted __be32 [usertype] sisr2
sound/soc/fsl/fsl_ssi.c:398:42: warning: incorrect type in argument 2 (different base types)
sound/soc/fsl/fsl_ssi.c:398:42: expected unsigned int [unsigned] [usertype] sisr
sound/soc/fsl/fsl_ssi.c:398:42: got restricted __be32 [addressable] [usertype] sisr
In other places where regmap_read() is used a u32 variable is passed
to store the register read value, so do the same here as well.
regmap API already takes care of endianness, so the usage of u32 is safe.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a partial revert (in a cleaner way) of commit ebf08ae3bc
("ASoC: fsl_ssi: Keep ssi->i2s_net updated") to fix a regression
at test cases when switching between mono and stereo audio.
The problem is that ssi->i2s_net is initialized in set_dai_fmt()
only, while this set_dai_fmt() is only called during the dai-link
probe(). The original patch assumed set_dai_fmt() would be called
during every playback instance, so it failed at the overriding use
cases.
This patch adds the local variable i2s_net back to let regular use
cases still follow the mode settings from the set_dai_fmt().
Meanwhile, the original commit of keeping ssi->i2s_net updated was
to make set_tdm_slot() clean by checking the ssi->i2s_net directly
instead of reading SCR register. However, the change itself is not
necessary (or even harmful) because the set_tdm_slot() might fail
to check the slot number for Normal-Mode-None-Net settings while
mono audio cases still need 2 slots. So this patch can also fix it.
And it adds an extra line of comments to declare ssi->i2s_net does
not reflect the register value but merely the initial setting from
the set_dai_fmt().
Reported-by: Mika Penttilä <mika.penttila@nextfour.com>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Mika Penttilä <mika.penttila@nextfour.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleans up probe() function by moving all Device Tree
related code into a separate function. It allows the probe() to
be Device Tree independent. This will be very useful for future
integration of imx-ssi driver which has similar functionalities
while exists only because it supports non-DT cases.
This patch also moves symmetric_channels of AC97 from the probe
to the structure snd_soc_dai_driver for simplification.
Additionally, since PowerPC and AC97 use the same pdev pointer
to register a platform device, this patch also unifies related
code.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The _fsl_ssi_set_dai_fmt() is a helper function being called from
fsl_ssi_set_dai_fmt() as an ASoC operation and fsl_ssi_hw_init()
mainly for AC97 format initialization.
This patch cleans the _fsl_ssi_set_dai_fmt() in following ways:
* Removing *dev pointer in the parameters as it's included in the
*ssi pointer of struct fsl_ssi.
* Using regmap_update_bits() instead of regmap_read() with masking
the value manually.
* Moving baudclk check to the switch-case routine to skip the I2S
master check. And moving SxCCR.DC settings after baudclk check.
* Adding format settings for SND_SOC_DAIFMT_AC97 like others.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
AC97 configures most of registers earlier to start a communication
with CODECs in order to successfully initialize CODEC. Currently,
_fsl_ssi_set_dai_fmt() and fsl_ssi_setup_ac97() are called to get
all SSI registers properly set.
Since now the driver has a fsl_ssi_hw_init() to handle all register
initial settings, this patch moves those register settings of AC97
to the fsl_ssi_hw_init() as well.
Meanwhile it applies _fsl_ssi_set_dai_fmt() call to AC97 only since
other formats would be configured via normal set_dai_fmt() directly.
This patch also adds fsl_ssi_hw_clean() to cleanup control bits for
AC97 in the platform remote() function.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The _fsl_ssi_set_dai_fmt() bypasses an undefined format for AC97
mode. However, it's not really necessary if AC97 has its complete
format defined.
So this patch adds a DAIFMT macro of complete format including a
clock direction and polarity.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The trigger() calls fsl_ssi_tx_config() and fsl_ssi_rx_config(),
and both of them jump to fsl_ssi_config(). And fsl_ssi_config()
later calls another fsl_ssi_rxtx_config().
However, the whole routine, especially fsl_ssi_config() function,
is too complicated because of the folowing reasons:
1) It has to handle the concern of the opposite stream.
2) It has to handle cases of offline configurations support.
3) It has to handle enable and disable operations while they're
mostly different.
Since the enable and disable routines have more differences than
TX and RX rountines, this patch simplifies these helper functions
with the following changes:
- Changing to two helper functions of enable and disable instead
of TX and RX.
- Removing fsl_ssi_rxtx_config() by separately integrating it to
two newly introduced enable & disable functions.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FIFO clear helper function is just one line of code now.
So it could be cleaned up by removing it and calling regmap
directly.
Meanwhile, FIFO clear could be applied to all use cases, not
confined to AC97. So this patch also moves FIFO clear in the
trigger() to fsl_ssi_config() and removes the AC97 check.
Note that SOR register is safe from offline_config HW limit.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The define of fsl_ssi_disable_val is not so clear as it mixes two
steps of calculations together. And those parameter names are also
a bit long to read.
Since it just tries to exclude the shared bits from the regvals of
current stream while the opposite stream is active, it's better to
use something like ssi_excl_shared_bits.
This patch also bisects fsl_ssi_disable_val into two macros of two
corresponding steps and then shortens its parameter names. It also
updates callers in the fsl_ssi_config() accordingly.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Checking TE and RE bits in SCR register doesn't work for AC97 mode
which enables SSIEN, TE and RE in the fsl_ssi_setup_ac97() that's
called during probe().
So when running into the trigger(), it will always get the result
of both TE and RE being enabled already, even if actually there is
no active stream.
This patch fixes this issue by adding a variable to log the active
streams manually.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch replaces the register read with ssi->i2s_net for
simplification. It also removes masking SSIEN from scr value
since it's handled later by regmap_update_bits() to set this
scr value back.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hw_params() overwrites i2s_net settings for special cases like
mono-channel support, however, it doesn't update ssi->i2s_net as
set_dai_fmt() does.
This patch removes the local i2s_net variable and directly updates
ssi->i2s_net in the hw_params() so that the driver can simply look
up the ssi->i2s_net instead of reading the register.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The RX and TX macros were defined implicitly and there was
a potential risk if someone changes their values.
Since they were defined to index the array ssi->regvals[2],
this patch moves these two macros to fsl_ssi.c, closer to
its owner ssi->regvals. And it also puts some comments here
to limit their value within [0, 1].
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'iprop' variable is passed as an argument to the be32_to_cpup()
function, which expects a 'const _be *' type.
Change the iprop variable type so that the following build warnings
with W=1 are gone:
sound/soc/fsl/fsl_ssi.c:1463:48: warning: incorrect type in argument 1 (different base types)
sound/soc/fsl/fsl_ssi.c:1463:48: expected restricted __be32 const [usertype] *p
sound/soc/fsl/fsl_ssi.c:1463:48: got unsigned int const [usertype] *[assigned] iprop
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The name fsl_ssi_rxtx_reg_val is too long to read comfortably.
So this patch shortens it by using an array (fsl_ssi_regvals,
renamed from fsl_ssi_reg_val). To do that, it also introduces
two macros (TX and RX) to replace the wrapper structure. This
will also help further cleanups.
Meanwhile, it unifies all local variable with the name "vals"
to get rid of the name "reg" -- could be confusing with "regs"
in the private struct for regmap.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch refines the comments by:
1) Removing all out-of-date comments
2) Removing all not-so-useful comments
3) Unifying the styles of all comments
4) Shortening comments to be more conise
5) Adding comments to improve code readablity
6) Moving all register related comments to fsl_ssi.h
7) Adding comments to all register and field defines
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When testing AC'97 capture on UDOO board (currently the only user of
fsl_ssi driver in the AC'97 mode) it become obvious that there is a massive
distortion above certain, small input signal.
This problem has been traced to silicon errata ERR003778:
"In AC97, 16-bit mode, received data is shifted by 4-bit locations" that
has "No fix scheduled".
This errata suggests a workaround of doing a 4-bit shift back in SDMA
script for this specific operation mode, however our SDMA scripts are
shared between various SoC peripherals so we can't really modify them.
There is a simple way to avoid this problem, however, that is to disallow
recording in 16-bit mode and only support it in AC'97-native 20-bit mode.
We have to use a 4-byte format for this since SSI FIFOs do not allow 3-byte
accesses (and these aren't supported by imx-sdma driver anyway).
With this change the capture distortion is gone.
We can also add this format as an additional one supported for playback,
using this opportunity to make sure that we use CPU-endian-native formats
in AC'97 mode as we already do in I2S mode.
There is no problem in using different bit widths in playback and capture
in AC'97 mode so allow this, too.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to make sure that only proper channel slots (in SACCST register)
are enabled at playback start time since some AC'97 CODECs (like VT1613 on
UDOO board) were observed requesting via SLOTREQ spurious ones just after
an AC'97 link is started but before the CODEC is configured by its driver.
When a bit for some channel slot is set in a SLOTREQ request then SSI sets
the relevant bit in SACCST automatically, which then 'sticks' until it is
manually unset.
The SACCST register is not writable directly, we have to use SACCDIS and
SACCEN registers to configure it instead (these aren't normal registers:
writing a '1' bit at some position in SACCEN sets the relevant bit in
SACCST; SACCDIS operates in a similar way but allows unsetting bits in
SACCST).
Theoretically, this should be necessary only for the very first playback
but since some CODECs are so untrustworthy and extra channel slots enabled
mean ruined playback let's play safe here and make sure that no extra
slots are enabled in SACCST every time a playback is started.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In AC'97 mode we configure and start SSI RX / TX on probe path via
a call to _fsl_ssi_set_dai_fmt() function.
We don't need to call this function again later and in fact don't want to
do it since this function temporarily sets STCR, SRCR and SCR to some
intermediate values.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need to set CCSR_SSI_SIER_RFF0_EN / CCSR_SSI_SIER_TFE0_EN bits
in reg->rx.sier / reg->tx.sier variables in a non-AC'97 mode considering we
had just initialized these variables to these very values unconditionally a
few lines earlier.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
