The code in asoc_simple_startup was treating any non-zero return from
snd_pcm_hw_constraint_minmax as an error, when this can return 1 in some
normal cases and only negative values indicate an error.
When this happened, it caused asoc_simple_startup to disable the clocks
it just enabled and return 1, which was not treated as an error by the
calling code which only checks for negative return values. Then when the
PCM is eventually shut down, it causes the clock framework to complain
about disabling clocks that were not enabled.
Fix the check for snd_pcm_hw_constraint_minmax return value to only
treat negative values as an error.
Fixes: 5ca2ab4598 ("ASoC: simple-card-utils: Add new system-clock-fixed flag")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20230602011936.231931-1-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Basically CPU and Platform are different Component, but if CPU is using
soc-generic-dmaengine-pcm, same dev will be shared between CPU and
Platform, and Simple Card had been supporting it.
When we focus to clean up Simple Card driver, we tend to remove platforms
if no Platform was selected, but it is wrong because of above reasons.
This patch adds comment why we shouldn't remove platforms.
In case of CPU is not using soc-generic-dmaengine-pcm, CPU and Platform
will be duplicated, but it will be ignored by snd_soc_rtd_add_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/875yattwqv.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a generic way to create jack inputs for auxiliary jack detection
drivers (e.g. via i2c, spi), which are not part of any real codec.
The simple-card can be used as combining card driver to add the jacks,
no new one is required.
Create a jack (for input-events) for jack devices in the auxiliary
device list (aux_devs). A device which returns a valid value on
get_jack_type counts as jack device; set_jack is required
to add the jack to the device.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230123135913.2720991-3-astrid.rost@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The "convert-xxx" properties only have an effect for DPCM DAI links.
A DAI link is only created as DPCM if the device tree requires it;
part of this involves checking for the use of "convert-xxx" properties.
When the convert-sample-format property was added, the checks got out
of sync. A DAI link that specified only convert-sample-format but did
not pass any of the other DPCM checks would not go into DPCM mode and
the convert-sample-format property would be silently ignored.
Fix this by adding a function to do the "convert-xxx" property checks,
instead of open-coding it in simple-card and audio-graph-card. And add
"convert-sample-format" to the check function so that DAI links using
it will be initialized correctly.
Fixes: 047a05366f ("ASoC: simple-card-utils: Fixup DAI sample format")
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Acked-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/20221019012302.633830-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current asoc_simple_init_for_codec2codec() adds default Codec2Codec
settings if rtd was Codec only.
But DPCM:BE also judged as Codec only, because dummy-DAI doesn't have
"endianness" (which is key parameter to judge as Codec).
This patch ignores setup Codec2Codec settings if it was DPCM:BE case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87a69ts950.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Charles Keepax <ckeepax@opensource.cirrus.com>:
Currently the set_fmt callback always passes clock provider/consumer
with respect to the CODEC. This made sense when the framework was
directly broken down into platforms and CODECs. However, as things
are now broken down into components which can be connected as either
the CPU or CODEC side of a DAI link it simplifies things if each
side of the link is just told if it is provider or consumer of the
clocks. Making this change allows us to remove one of the last parts
of the ASoC core that needs to know if a driver is a CODEC driver,
where it flips the clock format specifier if a CODEC driver is used on
the CPU side of a DAI link, as well as just being conceptually more
consistent with componentisation.
The basic idea of this patch chain is to change the set_fmt callback
from specifying if the CODEC is provider/consumer into directly
specifying if the component is provider/consumer. To do this we add
some new defines, and then to preserve bisectability, the migration is
done by adding a new callback, converting over all existing CPU side
drivers, converting the core, and then finally reverting back to the
old callback.
Converting the platform drivers makes sense as the existing defines
are from the perspective of the CODEC and there are more CODEC drivers
than platform drivers.
Obviously a fair amount of this patch chain I was only able to build
test, so any testing that can be done would be greatly appreciated.
commit 95cfc0a0aa ("ASoC: simple-card: Add support for
codec2codec DAI links") added the function
asoc_simple_init_dai_link_params() to initialize dai_link "params".
It is very straight naming, but difficult to noticed that it is for
Codec2Codec support. Handling Codec2Codec is one of very tricky part
on ALSA SoC, thus it is very important to clarify it. This patch
renames the function name.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o7zflk3n.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The helper function snd_soc_component_is_codec is based off the
presence of the non_legacy_dai_naming flag. This isn't super robust
as CPU side components may also specify this flag, and indeed the
kernel already contains a couple that do. After componentisation there
isn't really a totally robust solution to identifying what is a CODEC
driver, without introducing a flag specifically for that purpose, and
really the desirable direction to move in is that the distinction
doesn't matter.
This patch does two things to try to mitigate these problems. Firstly,
now that all the other users of the helper function have been removed,
it makes the helper function local to the driver rather, than being
part of the core. This should help to discourage any new code from
being created that depends on the CODEC driver distinction. Secondly,
it updates the helper function itself to use the endianness flag
rather than the non_legacy_dai_naming flag. The endianness flag is
definitely invalid on a CPU side component, so it a more reliable
indicator that the device is definitely a CODEC. The vast majority of
buses require the CODEC to set the endianness flag, so the number of
corner cases should be fairly minimal. It is worth noting that CODECs
sending audio over SPI, or built into the CPU CODECs are potential
corner cases, however the hope is that in most cases those types of
devices do not consitute a simple audio card.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220519154318.2153729-57-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_card_jack_new() allowed to create jack kcontrol without pins,
but did not create kcontrols. The jack would not have kcontrols if pins
were not going to be added.
This renames the old snd_soc_card_jack_new() to
snd_soc_card_jack_new_pins() for use when pins are provided or will be
added later. The new snd_soc_card_jack_new() appropriately creates a
jack for use without pins and adds a kcontrol.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Link: https://lore.kernel.org/r/20220408041114.6024-1-akihiko.odaki@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Playback or capture errors are seen when clock is reset during an active
stage of DAI. Presently this scenario happens when DAI has both playback
and capture sessions running and one of these finishes first which will
be followed by clock rate reset. The remaining active session will be
affected in such case.
Address this problem by allowing clock rate reset to happen only when
the DAI is no more active.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/1646910999-2501-1-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some audio hardware cannot support the same slot width for all sample
widths, or a slot width equal to the sample width for all sample widths.
This is usually due either to limitations of the audio serial port or
system clocking restrictions.
A typical example would be:
- 16-bit samples in 16-bit slots
- 24-bit samples in 32-bit slots
The new dai-tdm-slot-width-map property allows setting a mapping of
sample widths and the corresponding tdm slot widths and slot counts.
Although the slot count is usually the same for all cases this does
allow for adding padding slots to maintain the same bitclk frequency.
The property is added to each endpoint node that needs the component
DAI to be told the TDM slot width and count.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220228172754.453783-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new system-clock-fixed flag, which can be used to specify that the
driver cannot or should not allow the clock frequency of the mapped clock
to be modified. This behavior is also implied if the system-clock-frequency
parameter is set explicitly - the flag is meant for cases where a clock is
mapped to the DAI but which is, or should be treated as, fixed.
When mclk-fs is also specified, this causes a PCM constraint to be added
which enforces that only the corresponding valid sample rate can be used.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220120195832.1742271-7-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If an mclk-fs value was provided in the device tree configuration, the
calculated MCLK was fed into the downstream codec DAI and CPU DAI,
however set_sysclk was not being called on the platform device. Some
platform devices such as the Xilinx Audio Formatter need to know the MCLK
as well.
Call snd_soc_component_set_sysclk on each component in the stream to set
the proper sysclk value in addition to the existing call of
snd_soc_dai_set_sysclk on the codec DAI and CPU DAI. This may end up
resulting in redundant calls if one of the snd_soc_dai_set_sysclk calls
ends up calling snd_soc_component_set_sysclk itself, but that isn't
expected to cause any significant harm.
Fixes: f48dcbb6d4 ("ASoC: simple-card-utils: share asoc_simple_hw_param()")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20220120195832.1742271-5-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASoC core already has several helpers to parse card properties
from the device tree. Move the parsing code for "pin-switches" from
simple-card-utils to a shared snd_soc_of_parse_pin_switches() function
so other drivers can also use it to set up pin switches configured in
the device tree.
Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211214142049.20422-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The allocation of the DAI link components (DLCs) passed the wrong
pointer to sizeof. Since simple_dai_props is much larger than
snd_soc_dai_link_component, there was no out of bounds access, only
wasted memory.
Fixes: f2138aed23 ("ASoC: simple-card-utils: enable flexible CPU/Codec/Platform")
Fixes: 050c7950fd ("ASoC: simple-card-utils: alloc dai_link information for CPU/Codec/Platform")
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20210805050706.46833-1-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We couldn't setup dai_props cpu_dai/codec_dai at the initial timing,
because "counting DAIs loop" and "detecting DAIs loop" were different.
But we can do it now, because these are using same loops.
This patch setups dai_props cpu_dai/codec_dai at the initial timing.
It can removes triky code from simple-card / audio-graph.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tuocwfa8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current simple-card / audio-graph creates 1xCPU + 1xCodec + 1xPlatform
for all dai_link, but some of them is not needed.
For example Platform is not needed for DPCM BE case.
Moreover, we can share snd-soc-dummy DAI for CPU-dummy / dummy-Codec
in DPCM.
This patch adds dummy DAI and share it when DPCM case,
I beliave it can contribute to reduce memory.
By this patch, CPU-dummy / dummy-CPU are set at asoc_simple_init_priv(),
thus, its settings are no longer needed at DPCM detecting timing
on simple-card / audio-graph.
Moreover, we can remove triky Platform settings code for DPCM BE,
because un-needed Platform is not created.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tuoqod22.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA: control - add generic LED API
This patchset tries to resolve the diversity in the audio LED
control among the ALSA drivers. A new control layer registration
is introduced which allows to run additional operations on
top of the elementary ALSA sound controls.
A new control access group (three bits in the access flags)
was introduced to carry the LED group information for
the sound controls. The low-level sound drivers can just
mark those controls using this access group. This information
is not exported to the user space, but user space can
manage the LED sound control associations through sysfs
(last patch) per Mark's request. It makes things fully
configurable in the kernel and user space (UCM).
The actual state ('route') evaluation is really easy
(the minimal value check for all channels / controls / cards).
If there's more complicated logic for a given hardware,
the card driver may eventually export a new read-only
sound control for the LED group and do the logic itself.
The new LED trigger control code is completely separated
and possibly optional (there's no symbol dependency).
The full code separation allows eventually to move this
LED trigger control to the user space in future.
Actually it replaces the already present functionality
in the kernel space (HDA drivers) and allows a quick adoption
for the recent hardware (ASoC codecs including SoundWire).
snd_ctl_led 24576 0
The sound driver implementation is really easy:
1) call snd_ctl_led_request() when control LED layer should be
automatically activated
/ it calls module_request("snd-ctl-led") on demand /
2) mark all related kcontrols with
SNDRV_CTL_ELEM_ACCESS_SPK_LED or
SNDRV_CTL_ELEM_ACCESS_MIC_LED
Link: https://lore.kernel.org/r/20210317172945.842280-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
simple-card / audio-graph are assuming single CPU/Codec/Platform on
dai_link. Because of it, it is difficult to support Multi-CPU/Codec.
This patch allocs CPU/Codec/Platform dai_link imformation
instead of using existing props information. It can update to
multi-CPU/Codec, but is still assuming single-CPU/Codec for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87blb61tpv.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 1e30f642cf ("ASoC: simple-card-utils: Fix device
module clock"). The original patch ended up breaking following platform,
which depends on set_sysclk() to configure internal PLL on wm8904 codec
and expects simple-card-utils to not update the MCLK rate.
- "arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts"
It would be best if codec takes care of setting MCLK clock via DAI
set_sysclk() callback.
Reported-by: Michael Walle <michael@walle.cc>
Suggested-by: Mark Brown <broonie@kernel.org>
Suggested-by: Michael Walle <michael@walle.cc>
Fixes: 1e30f642cf ("ASoC: simple-card-utils: Fix device module clock")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/1615829492-8972-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If "clocks = <&xxx>" is specified from the CPU or Codec component
device node, the clock is not getting enabled. Thus audio playback
or capture fails.
Fix this by populating "simple_dai->clk" field when clocks property
is specified from device node as well. Also tidy up by re-organising
conditional statements of parsing logic.
Fixes: bb6fc620c2 ("ASoC: simple-card-utils: add asoc_simple_card_parse_clk()")
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1612939421-19900-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
