Each SoundWire peripheral can be programmed from the manager side
either with a regular command FIFO, or with the HDaudio CORB/RIRB
DMA-based mechanism. The mapping between SoundWire peripheral and SDI
address is handled with the LSDIID register.
This mapping only works of course if each peripheral has a unique
address across all links. This has already been enforced in previous
Intel contributions allowing for an IDA-based solution for the device
number allocation.
The checks on the dev_num are handled at the SoundWire level, but the
locking is handled at the hda-mlink level.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-16-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These helpers configure the ratio between the base clock and the
hardware signal used for link synchronization.
The SYNCPRD is written before the first sublink is powered-up. The
SYNCPU bit is set, but it will only be cleared after the link is
powered-up, hence the implementation with a set/wait pattern.
These helpers are currently only needed by SoundWire support, where
the lock is taken at a higher level, so only the _unlocked versions
are exposed for now.
Note that the _wait_bit() implementation is similar to previous
helpers in drivers/soundwire, but with sleep duration and timeout
aligned with hardware recommendations. If desired, this helper could
be modified in a second step with e.g. readl_poll_timeout().
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-13-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helpers to program SPA/CPA bits, using a mutex to access the
shared LCTL register if required.
All links are managed with the same LCTLx.SPA bits. However there are
quite a few implementation details to be aware of:
Legacy HDaudio multi-links are powered-up when exiting reset, which
requires the ref_count to be manually set to one when initializing the
link.
Alternate links for SoundWire/DMIC/SSP need to be explicitly
powered-up before accessing the SHIM/IP/Vendor-Specific SHIM space for
each sublink. DMIC/SSP/SoundWire are all different cases with a
different device/dai/hlink relationship.
SoundWire will handle power management with the auxiliary device
resume/suspend routine. The ref_count is not necessary in this case.
The DMIC/SSP will by contrast handle the power management from DAI
.startup and .shutdown callbacks.
The SSP has a 1:1 mapping between sublink and DAI, but it's
bidirectional so the ref_count will help avoid turning off the sublink
when one of the two directions is still in use.
The DMIC has a single link but two DAIs for data generated at
different sampling frequencies, again the ref_count will make sure the
two DAIs can be used concurrently.
And last the SoundWire Intel require power-up/down and bank switch to
be handled with a lock already taken, so the 'eml_lock' is made
optional with the _unlocked versions of the helpers.
Note that the _check_power_active() implementation is similar to
previous helpers in sound/hda/ext, with sleep duration and timeout
aligned with hardware recommendations. If desired, this helper could
be modified in a second step with .e.g. readl_poll_timeout()
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-9-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend hdac_ext_link to store information needed for ALT
links. Follow-up patches will include more functional patches for
power-up and down.
Note that this patch suggests the use of an 'eml_lock' to serialize
access to shared registers. SoundWire-specific sequence require the
lock to be taken at a higher level, as a result the helpers added in
follow-up patches will provide 'unlocked' versions when needed.
Also note that the low-level sequences with the 'hdaml_' prefix are
taken directly from the hardware specifications - naming conventions
included. The code will be split in two, with locking and linked-list
management handled separately to avoid mixing required hardware setup
and Linux-based resource management.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
