Input: gpio_tilt - delete driver

This driver was merged in 2011 as a tool for detecting the orientation
of a screen. The device driver assumes board file setup using the
platform data from <linux/input/gpio_tilt.h>. But no boards in the
kernel tree defines this platform data.

As I am faced with refactoring drivers to use GPIO descriptors and
pass decriptor tables from boards, or use the device tree device
drivers like these creates a serious problem: I cannot fix them and
cannot test them, not even compile-test them with a system actually
using it (no in-tree boardfile).

I suggest to delete this driver and rewrite it using device tree if
it is still in use on actively maintained systems.

I can also offer to rewrite it out of the blue using device tree if
someone promise to test it and help me iterate it.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Patchwork-Id: 10133609
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Documentation/input/devices/gpio-tilt.rst

@@ -1,103 +0,0 @@
-Driver for tilt-switches connected via GPIOs
-============================================
-
-Generic driver to read data from tilt switches connected via gpios.
-Orientation can be provided by one or more than one tilt switches,
-i.e. each tilt switch providing one axis, and the number of axes
-is also not limited.
-
-
-Data structures
----------------
-
-The array of struct gpio in the gpios field is used to list the gpios
-that represent the current tilt state.
-
-The array of struct gpio_tilt_axis describes the axes that are reported
-to the input system. The values set therein are used for the
-input_set_abs_params calls needed to init the axes.
-
-The array of struct gpio_tilt_state maps gpio states to the corresponding
-values to report. The gpio state is represented as a bitfield where the
-bit-index corresponds to the index of the gpio in the struct gpio array.
-In the same manner the values stored in the axes array correspond to
-the elements of the gpio_tilt_axis-array.
-
-
-Example
--------
-
-Example configuration for a single TS1003 tilt switch that rotates around
-one axis in 4 steps and emits the current tilt via two GPIOs::
-
-    static int sg060_tilt_enable(struct device *dev) {
-	    /* code to enable the sensors */
-    };
-
-    static void sg060_tilt_disable(struct device *dev) {
-	    /* code to disable the sensors */
-    };
-
-    static struct gpio sg060_tilt_gpios[] = {
-	    { SG060_TILT_GPIO_SENSOR1, GPIOF_IN, "tilt_sensor1" },
-	    { SG060_TILT_GPIO_SENSOR2, GPIOF_IN, "tilt_sensor2" },
-    };
-
-    static struct gpio_tilt_state sg060_tilt_states[] = {
-	    {
-		    .gpios = (0 << 1) | (0 << 0),
-		    .axes = (int[]) {
-			    0,
-		    },
-	    }, {
-		    .gpios = (0 << 1) | (1 << 0),
-		    .axes = (int[]) {
-			    1, /* 90 degrees */
-		    },
-	    }, {
-		    .gpios = (1 << 1) | (1 << 0),
-		    .axes = (int[]) {
-			    2, /* 180 degrees */
-		    },
-	    }, {
-		    .gpios = (1 << 1) | (0 << 0),
-		    .axes = (int[]) {
-			    3, /* 270 degrees */
-		    },
-	    },
-    };
-
-    static struct gpio_tilt_axis sg060_tilt_axes[] = {
-	    {
-		    .axis = ABS_RY,
-		    .min = 0,
-		    .max = 3,
-		    .fuzz = 0,
-		    .flat = 0,
-	    },
-    };
-
-    static struct gpio_tilt_platform_data sg060_tilt_pdata= {
-	    .gpios = sg060_tilt_gpios,
-	    .nr_gpios = ARRAY_SIZE(sg060_tilt_gpios),
-
-	    .axes = sg060_tilt_axes,
-	    .nr_axes = ARRAY_SIZE(sg060_tilt_axes),
-
-	    .states = sg060_tilt_states,
-	    .nr_states = ARRAY_SIZE(sg060_tilt_states),
-
-	    .debounce_interval = 100,
-
-	    .poll_interval = 1000,
-	    .enable = sg060_tilt_enable,
-	    .disable = sg060_tilt_disable,
-    };
-
-    static struct platform_device sg060_device_tilt = {
-	    .name = "gpio-tilt-polled",
-	    .id = -1,
-	    .dev = {
-		    .platform_data = &sg060_tilt_pdata,
-	    },
-    };