Merge tag 'soc-fixes-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC DT and driver fixes from Arnd Bergmann:
 "Lots of dts fixes for Qualcomm Snapdragon and NXP i.MX platforms,
  including:

   - A regression fix for SDHCI controllers on Inforce 6540, and another
     SDHCI fix on SM8350

   - Reenable cluster idle on sm8250 after the the code fix is upstream

   - multiple fixes for the QMP PHY binding, needing an incompatible dt
     change

   - The reserved memory map is updated on Xiaomi Mi 4C and Huawei Nexus
     6P, to avoid instabilities caused by use of protected memory
     regions

   - Fix i.MX8MP DT for missing GPC Interrupt, power-domain typo and USB
     clock error

   - A couple of verdin-imx8mm DT fixes for audio playback support

   - Fix pca9547 i2c-mux node name for i.MX and Vybrid device trees

   - Fix an imx93-11x11-evk uSDHC pad setting problem that causes Micron
     eMMC CMD8 CRC error in HS400ES/HS400 mode

  The remaining ARM and RISC-V platforms only have very few smaller dts
  bugfixes this time:

   - A fix for the SiFive unmatched board's PCI memory space

   - A revert to fix a regression with GPIO on Marvell Armada

   - A fix for the UART address on Marvell AC5

   - Missing chip-select phandles for stm32 boards

   - Selecting the correct clock for the sam9x60 memory controller

   - Amlogic based Odroid-HC4 needs a revert to restore USB
     functionality.

  And finally, there are some minor code fixes:

   - Build fixes for OMAP1, pxa, riscpc, raspberry pi firmware, and zynq
     firmware

   - memory controller driver fixes for an OMAP regression and older
     bugs on tegra, atmel and mvebu

   - reset controller fixes for ti-sci and uniphier platforms

   - ARM SCMI firmware fixes for a couple of rare corner cases

   - Qualcomm platform driver fixes for incorrect error handling and a
     backwards compatibility fix for the apr driver using older dtb

   - NXP i.MX SoC driver fixes for HDMI output, error handling in the
     imx8 soc-id and missing reference counting on older cpuid code"

* tag 'soc-fixes-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (60 commits)
  firmware: zynqmp: fix declarations for gcc-13
  ARM: dts: stm32: Fix qspi pinctrl phandle for stm32mp151a-prtt1l
  ARM: dts: stm32: Fix qspi pinctrl phandle for stm32mp157c-emstamp-argon
  ARM: dts: stm32: Fix qspi pinctrl phandle for stm32mp15xx-dhcom-som
  ARM: dts: stm32: Fix qspi pinctrl phandle for stm32mp15xx-dhcor-som
  ARM: dts: at91: sam9x60: fix the ddr clock for sam9x60
  ARM: omap1: fix building gpio15xx
  ARM: omap1: fix !ARCH_OMAP1_ANY link failures
  firmware: raspberrypi: Fix type assignment
  arm64: dts: qcom: msm8992-libra: Fix the memory map
  arm64: dts: qcom: msm8992: Don't use sfpb mutex
  PM: AVS: qcom-cpr: Fix an error handling path in cpr_probe()
  arm64: dts: msm8994-angler: fix the memory map
  arm64: dts: marvell: AC5/AC5X: Fix address for UART1
  ARM: footbridge: drop unnecessary inclusion
  Revert "ARM: dts: armada-39x: Fix compatible string for gpios"
  Revert "ARM: dts: armada-38x: Fix compatible string for gpios"
  ARM: pxa: enable PXA310/PXA320 for DT-only build
  riscv: dts: sifive: fu740: fix size of pcie 32bit memory
  soc: qcom: apr: Make qcom,protection-domain optional again
  ...

Documentation/devicetree/bindings/soc/qcom/qcom,apr-services.yaml

@@ -39,8 +39,8 @@ properties:
   qcom,protection-domain:
     $ref: /schemas/types.yaml#/definitions/string-array
     description: |
-      Protection domain service name and path for APR service
+      Protection domain service name and path for APR service (if supported).
-      possible values are::
+      Possible values are::
       "avs/audio", "msm/adsp/audio_pd".
       "kernel/elf_loader", "msm/modem/wlan_pd".
       "tms/servreg", "msm/adsp/audio_pd".
@@ -49,6 +49,5 @@ properties:
 
 required:
   - reg
-  - qcom,protection-domain
 
 additionalProperties: true

arch/arm/boot/dts/armada-38x.dtsi

@@ -304,7 +304,7 @@
 			};
 
 			gpio0: gpio@18100 {
-				compatible = "marvell,armadaxp-gpio",
+				compatible = "marvell,armada-370-gpio",
 					     "marvell,orion-gpio";
 				reg = <0x18100 0x40>, <0x181c0 0x08>;
 				reg-names = "gpio", "pwm";
@@ -323,7 +323,7 @@
 			};
 
 			gpio1: gpio@18140 {
-				compatible = "marvell,armadaxp-gpio",
+				compatible = "marvell,armada-370-gpio",
 					     "marvell,orion-gpio";
 				reg = <0x18140 0x40>, <0x181c8 0x08>;
 				reg-names = "gpio", "pwm";

arch/arm/boot/dts/armada-39x.dtsi

@@ -213,7 +213,7 @@
 			};
 
 			gpio0: gpio@18100 {
-				compatible = "marvell,armadaxp-gpio", "marvell,orion-gpio";
+				compatible = "marvell,orion-gpio";
 				reg = <0x18100 0x40>;
 				ngpios = <32>;
 				gpio-controller;
@@ -227,7 +227,7 @@
 			};
 
 			gpio1: gpio@18140 {
-				compatible = "marvell,armadaxp-gpio", "marvell,orion-gpio";
+				compatible = "marvell,orion-gpio";
 				reg = <0x18140 0x40>;
 				ngpios = <28>;
 				gpio-controller;

arch/arm/boot/dts/imx53-ppd.dts

@@ -488,7 +488,7 @@
 	scl-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9547";
 		#address-cells = <1>;
 		#size-cells = <0>;

arch/arm/boot/dts/imx6qdl-gw560x.dtsi

@@ -632,7 +632,6 @@
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
-	uart-has-rtscts;
 	rts-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6ul-pico-dwarf.dts

@@ -32,7 +32,7 @@
 };
 
 &i2c2 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";

arch/arm/boot/dts/imx7d-pico-dwarf.dts

@@ -32,7 +32,7 @@
 };
 
 &i2c1 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
@@ -52,7 +52,7 @@
 };
 
 &i2c4 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";

arch/arm/boot/dts/imx7d-pico-nymph.dts

@@ -43,7 +43,7 @@
 };
 
 &i2c1 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
@@ -64,7 +64,7 @@
 };
 
 &i2c2 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";

arch/arm/boot/dts/qcom-apq8084-ifc6540.dts

@@ -19,16 +19,16 @@
 		serial@f995e000 {
 			status = "okay";
 		};
-
-		sdhci@f9824900 {
-			bus-width = <8>;
-			non-removable;
-			status = "okay";
-		};
-
-		sdhci@f98a4900 {
-			cd-gpios = <&tlmm 122 GPIO_ACTIVE_LOW>;
-			bus-width = <4>;
-		};
 	};
 };
+
+&sdhc_1 {
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&tlmm 122 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+};

arch/arm/boot/dts/qcom-apq8084.dtsi

@@ -421,7 +421,7 @@
 			status = "disabled";
 		};
 
-		mmc@f9824900 {
+		sdhc_1: mmc@f9824900 {
 			compatible = "qcom,apq8084-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
 			reg-names = "hc", "core";
@@ -434,7 +434,7 @@
 			status = "disabled";
 		};
 
-		mmc@f98a4900 {
+		sdhc_2: mmc@f98a4900 {
 			compatible = "qcom,apq8084-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
 			reg-names = "hc", "core";

arch/arm/boot/dts/sam9x60.dtsi

@@ -564,7 +564,7 @@
 			mpddrc: mpddrc@ffffe800 {
 				compatible = "microchip,sam9x60-ddramc", "atmel,sama5d3-ddramc";
 				reg = <0xffffe800 0x200>;
-				clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_CORE PMC_MCK>;
+				clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_PERIPHERAL 49>;
 				clock-names = "ddrck", "mpddr";
 			};
 

arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi

@@ -101,8 +101,12 @@
 
 &qspi {
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+	pinctrl-0 = <&qspi_clk_pins_a
-	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
 	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
 	#address-cells = <1>;
 	#size-cells = <0>;

arch/arm/boot/dts/stm32mp157c-emstamp-argon.dtsi

@@ -391,8 +391,12 @@
 
 &qspi {
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+	pinctrl-0 = <&qspi_clk_pins_a
-	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
 	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
 	#address-cells = <1>;
 	#size-cells = <0>;

arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi

@@ -428,8 +428,12 @@
 
 &qspi {
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+	pinctrl-0 = <&qspi_clk_pins_a
-	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
 	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
 	#address-cells = <1>;
 	#size-cells = <0>;

arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi

@@ -247,8 +247,12 @@
 
 &qspi {
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+	pinctrl-0 = <&qspi_clk_pins_a
-	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
 	reg = <0x58003000 0x1000>, <0x70000000 0x200000>;
 	#address-cells = <1>;
 	#size-cells = <0>;

arch/arm/boot/dts/vf610-zii-dev-rev-b.dts

@@ -345,7 +345,7 @@
 };
 
 &i2c2 {
-	tca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		pinctrl-0 = <&pinctrl_i2c_mux_reset>;
 		pinctrl-names = "default";

arch/arm/boot/dts/vf610-zii-dev-rev-c.dts

@@ -340,7 +340,7 @@
 };
 
 &i2c2 {
-	tca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		pinctrl-0 = <&pinctrl_i2c_mux_reset>;
 		pinctrl-names = "default";

arch/arm/mach-footbridge/isa-rtc.c

@@ -20,7 +20,6 @@
 
 #include <linux/init.h>
 #include <linux/mc146818rtc.h>
-#include <linux/bcd.h>
 #include <linux/io.h>
 
 #include "common.h"

arch/arm/mach-imx/cpu-imx25.c

@@ -23,6 +23,7 @@ static int mx25_read_cpu_rev(void)
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx25-iim");
 	iim_base = of_iomap(np, 0);
+	of_node_put(np);
 	BUG_ON(!iim_base);
 	rev = readl(iim_base + MXC_IIMSREV);
 	iounmap(iim_base);

arch/arm/mach-imx/cpu-imx27.c

@@ -28,6 +28,7 @@ static int mx27_read_cpu_rev(void)
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx27-ccm");
 	ccm_base = of_iomap(np, 0);
+	of_node_put(np);
 	BUG_ON(!ccm_base);
 	/*
 	 * now we have access to the IO registers. As we need

arch/arm/mach-imx/cpu-imx31.c

@@ -39,6 +39,7 @@ static int mx31_read_cpu_rev(void)
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx31-iim");
 	iim_base = of_iomap(np, 0);
+	of_node_put(np);
 	BUG_ON(!iim_base);
 
 	/* read SREV register from IIM module */

arch/arm/mach-imx/cpu-imx35.c

@@ -21,6 +21,7 @@ static int mx35_read_cpu_rev(void)
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx35-iim");
 	iim_base = of_iomap(np, 0);
+	of_node_put(np);
 	BUG_ON(!iim_base);
 
 	rev = imx_readl(iim_base + MXC_IIMSREV);

arch/arm/mach-imx/cpu-imx5.c

@@ -28,6 +28,7 @@ static u32 imx5_read_srev_reg(const char *compat)
 
 	np = of_find_compatible_node(NULL, NULL, compat);
 	iim_base = of_iomap(np, 0);
+	of_node_put(np);
 	WARN_ON(!iim_base);
 
 	srev = readl(iim_base + IIM_SREV) & 0xff;

arch/arm/mach-omap1/Kconfig

@@ -4,6 +4,7 @@ menuconfig ARCH_OMAP1
 	depends on ARCH_MULTI_V4T || ARCH_MULTI_V5
 	depends on CPU_LITTLE_ENDIAN
 	depends on ATAGS
+	select ARCH_OMAP
 	select ARCH_HAS_HOLES_MEMORYMODEL
 	select ARCH_OMAP
 	select CLKSRC_MMIO
@@ -45,10 +46,6 @@ config ARCH_OMAP16XX
 	select CPU_ARM926T
 	select OMAP_DM_TIMER
 
-config ARCH_OMAP1_ANY
-	select ARCH_OMAP
-	def_bool ARCH_OMAP730 || ARCH_OMAP850 || ARCH_OMAP15XX || ARCH_OMAP16XX
-
 config ARCH_OMAP
 	bool
 

arch/arm/mach-omap1/Makefile

@@ -3,8 +3,6 @@
 # Makefile for the linux kernel.
 #
 
-ifdef CONFIG_ARCH_OMAP1_ANY
-
 # Common support
 obj-y := io.o id.o sram-init.o sram.o time.o irq.o mux.o flash.o \
 	 serial.o devices.o dma.o omap-dma.o fb.o
@@ -59,5 +57,3 @@ obj-$(CONFIG_ARCH_OMAP730)		+= gpio7xx.o
 obj-$(CONFIG_ARCH_OMAP850)		+= gpio7xx.o
 obj-$(CONFIG_ARCH_OMAP15XX)		+= gpio15xx.o
 obj-$(CONFIG_ARCH_OMAP16XX)		+= gpio16xx.o
-
-endif

arch/arm/mach-omap1/gpio15xx.c

@@ -11,6 +11,7 @@
 #include <linux/gpio.h>
 #include <linux/platform_data/gpio-omap.h>
 #include <linux/soc/ti/omap1-soc.h>
+#include <asm/irq.h>
 
 #include "irqs.h"
 

arch/arm/mach-omap1/io.c

@@ -22,17 +22,14 @@
  * The machine specific code may provide the extra mapping besides the
  * default mapping provided here.
  */
-static struct map_desc omap_io_desc[] __initdata = {
+#if defined (CONFIG_ARCH_OMAP730) || defined (CONFIG_ARCH_OMAP850)
+static struct map_desc omap7xx_io_desc[] __initdata = {
 	{
 		.virtual	= OMAP1_IO_VIRT,
 		.pfn		= __phys_to_pfn(OMAP1_IO_PHYS),
 		.length		= OMAP1_IO_SIZE,
 		.type		= MT_DEVICE
-	}
+	},
-};
-
-#if defined (CONFIG_ARCH_OMAP730) || defined (CONFIG_ARCH_OMAP850)
-static struct map_desc omap7xx_io_desc[] __initdata = {
 	{
 		.virtual	= OMAP7XX_DSP_BASE,
 		.pfn		= __phys_to_pfn(OMAP7XX_DSP_START),
@@ -49,6 +46,12 @@ static struct map_desc omap7xx_io_desc[] __initdata = {
 
 #ifdef CONFIG_ARCH_OMAP15XX
 static struct map_desc omap1510_io_desc[] __initdata = {
+	{
+		.virtual	= OMAP1_IO_VIRT,
+		.pfn		= __phys_to_pfn(OMAP1_IO_PHYS),
+		.length		= OMAP1_IO_SIZE,
+		.type		= MT_DEVICE
+	},
 	{
 		.virtual	= OMAP1510_DSP_BASE,
 		.pfn		= __phys_to_pfn(OMAP1510_DSP_START),
@@ -65,6 +68,12 @@ static struct map_desc omap1510_io_desc[] __initdata = {
 
 #if defined(CONFIG_ARCH_OMAP16XX)
 static struct map_desc omap16xx_io_desc[] __initdata = {
+	{
+		.virtual	= OMAP1_IO_VIRT,
+		.pfn		= __phys_to_pfn(OMAP1_IO_PHYS),
+		.length		= OMAP1_IO_SIZE,
+		.type		= MT_DEVICE
+	},
 	{
 		.virtual	= OMAP16XX_DSP_BASE,
 		.pfn		= __phys_to_pfn(OMAP16XX_DSP_START),
@@ -79,18 +88,9 @@ static struct map_desc omap16xx_io_desc[] __initdata = {
 };
 #endif
 
-/*
- * Maps common IO regions for omap1
- */
-static void __init omap1_map_common_io(void)
-{
-	iotable_init(omap_io_desc, ARRAY_SIZE(omap_io_desc));
-}
-
 #if defined (CONFIG_ARCH_OMAP730) || defined (CONFIG_ARCH_OMAP850)
 void __init omap7xx_map_io(void)
 {
-	omap1_map_common_io();
 	iotable_init(omap7xx_io_desc, ARRAY_SIZE(omap7xx_io_desc));
 }
 #endif
@@ -98,7 +98,6 @@ void __init omap7xx_map_io(void)
 #ifdef CONFIG_ARCH_OMAP15XX
 void __init omap15xx_map_io(void)
 {
-	omap1_map_common_io();
 	iotable_init(omap1510_io_desc, ARRAY_SIZE(omap1510_io_desc));
 }
 #endif
@@ -106,7 +105,6 @@ void __init omap15xx_map_io(void)
 #if defined(CONFIG_ARCH_OMAP16XX)
 void __init omap16xx_map_io(void)
 {
-	omap1_map_common_io();
 	iotable_init(omap16xx_io_desc, ARRAY_SIZE(omap16xx_io_desc));
 }
 #endif

arch/arm/mach-omap1/mcbsp.c

@@ -89,7 +89,6 @@ static struct omap_mcbsp_ops omap1_mcbsp_ops = {
 #define OMAP1610_MCBSP2_BASE	0xfffb1000
 #define OMAP1610_MCBSP3_BASE	0xe1017000
 
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
 struct resource omap7xx_mcbsp_res[][6] = {
 	{
 		{
@@ -159,14 +158,7 @@ static struct omap_mcbsp_platform_data omap7xx_mcbsp_pdata[] = {
 };
 #define OMAP7XX_MCBSP_RES_SZ		ARRAY_SIZE(omap7xx_mcbsp_res[1])
 #define OMAP7XX_MCBSP_COUNT		ARRAY_SIZE(omap7xx_mcbsp_res)
-#else
-#define omap7xx_mcbsp_res_0		NULL
-#define omap7xx_mcbsp_pdata		NULL
-#define OMAP7XX_MCBSP_RES_SZ		0
-#define OMAP7XX_MCBSP_COUNT		0
-#endif
 
-#ifdef CONFIG_ARCH_OMAP15XX
 struct resource omap15xx_mcbsp_res[][6] = {
 	{
 		{
@@ -266,14 +258,7 @@ static struct omap_mcbsp_platform_data omap15xx_mcbsp_pdata[] = {
 };
 #define OMAP15XX_MCBSP_RES_SZ		ARRAY_SIZE(omap15xx_mcbsp_res[1])
 #define OMAP15XX_MCBSP_COUNT		ARRAY_SIZE(omap15xx_mcbsp_res)
-#else
-#define omap15xx_mcbsp_res_0		NULL
-#define omap15xx_mcbsp_pdata		NULL
-#define OMAP15XX_MCBSP_RES_SZ		0
-#define OMAP15XX_MCBSP_COUNT		0
-#endif
 
-#ifdef CONFIG_ARCH_OMAP16XX
 struct resource omap16xx_mcbsp_res[][6] = {
 	{
 		{
@@ -373,12 +358,6 @@ static struct omap_mcbsp_platform_data omap16xx_mcbsp_pdata[] = {
 };
 #define OMAP16XX_MCBSP_RES_SZ		ARRAY_SIZE(omap16xx_mcbsp_res[1])
 #define OMAP16XX_MCBSP_COUNT		ARRAY_SIZE(omap16xx_mcbsp_res)
-#else
-#define omap16xx_mcbsp_res_0		NULL
-#define omap16xx_mcbsp_pdata		NULL
-#define OMAP16XX_MCBSP_RES_SZ		0
-#define OMAP16XX_MCBSP_COUNT		0
-#endif
 
 static void omap_mcbsp_register_board_cfg(struct resource *res, int res_count,
 			struct omap_mcbsp_platform_data *config, int size)

arch/arm/mach-omap1/pm.h

@@ -106,13 +106,6 @@
 #define OMAP7XX_IDLECT3		0xfffece24
 #define OMAP7XX_IDLE_LOOP_REQUEST	0x0C00
 
-#if     !defined(CONFIG_ARCH_OMAP730) && \
-	!defined(CONFIG_ARCH_OMAP850) && \
-	!defined(CONFIG_ARCH_OMAP15XX) && \
-	!defined(CONFIG_ARCH_OMAP16XX)
-#warning "Power management for this processor not implemented yet"
-#endif
-
 #ifndef __ASSEMBLER__
 
 #include <linux/clk.h>

arch/arm/mach-pxa/Kconfig

@@ -45,6 +45,8 @@ config MACH_PXA27X_DT
 config MACH_PXA3XX_DT
 	bool "Support PXA3xx platforms from device tree"
 	select CPU_PXA300
+	select CPU_PXA310
+	select CPU_PXA320
 	select PINCTRL
 	select POWER_SUPPLY
 	select PXA3xx

arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts

@@ -131,10 +131,6 @@
 };
 
 &usb {
-	phys = <&usb2_phy1>;
+	phys = <&usb2_phy0>, <&usb2_phy1>;
-	phy-names = "usb2-phy1";
+	phy-names = "usb2-phy0", "usb2-phy1";
-};
-
-&usb2_phy0 {
-	status = "disabled";
 };

arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts

@@ -110,7 +110,7 @@
 &i2c0 {
 	status = "okay";
 
-	pca9547@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;

arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts

@@ -89,7 +89,7 @@
 &i2c0 {
 	status = "okay";
 
-	pca9547@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;

arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts

@@ -88,7 +88,7 @@
 &i2c0 {
 	status = "okay";
 
-	pca9547@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;

arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts

@@ -53,7 +53,7 @@
 &i2c0 {
 	status = "okay";
 
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;

arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts

@@ -136,7 +136,7 @@
 &i2c0 {
 	status = "okay";
 
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;

arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts

@@ -245,7 +245,7 @@
 &i2c3 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9540";
 		#address-cells = <1>;
 		#size-cells = <0>;

arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi

@@ -103,7 +103,7 @@
 
 &i2c0 {
 	status = "okay";
-	pca9547@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
 		#address-cells = <1>;

arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi

@@ -44,7 +44,7 @@
 
 &i2c0 {
 	status = "okay";
-	pca9547@75 {
+	i2c-mux@75 {
 		compatible = "nxp,pca9547";
 		reg = <0x75>;
 		#address-cells = <1>;

arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi

@@ -54,7 +54,7 @@
 &i2c0 {
 	status = "okay";
 
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		#address-cells = <1>;
 		#size-cells = <0>;

arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi

@@ -120,7 +120,7 @@
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_espi2>;
-	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	eeprom@0 {
@@ -316,7 +316,7 @@
 			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x82
 			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x82
 			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x82
-			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x41
+			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13              0x41
 		>;
 	};
 

arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts

@@ -275,7 +275,7 @@
 		compatible = "rohm,bd71847";
 		reg = <0x4b>;
 		#clock-cells = <0>;
-		clocks = <&clk_xtal32k 0>;
+		clocks = <&clk_xtal32k>;
 		clock-output-names = "clk-32k-out";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_pmic>;

arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts

@@ -214,7 +214,7 @@
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
-	i2cmux@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9540";
 		reg = <0x70>;
 		#address-cells = <1>;

arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts

@@ -771,6 +771,7 @@
 &usbotg2 {
 	dr_mode = "host";
 	vbus-supply = <&reg_usb2_vbus>;
+	over-current-active-low;
 	status = "okay";
 };
 

arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi

@@ -9,6 +9,7 @@
 		simple-audio-card,bitclock-master = <&dailink_master>;
 		simple-audio-card,format = "i2s";
 		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,mclk-fs = <256>;
 		simple-audio-card,name = "imx8mm-wm8904";
 		simple-audio-card,routing =
 			"Headphone Jack", "HPOUTL",

arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi

@@ -11,6 +11,7 @@
 		simple-audio-card,bitclock-master = <&dailink_master>;
 		simple-audio-card,format = "i2s";
 		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,mclk-fs = <256>;
 		simple-audio-card,name = "imx8mm-nau8822";
 		simple-audio-card,routing =
 			"Headphones", "LHP",

arch/arm64/boot/dts/freescale/imx8mp-evk.dts

@@ -36,8 +36,8 @@
 
 	pcie0_refclk: pcie0-refclk {
 		compatible = "fixed-clock";
-			#clock-cells = <0>;
+		#clock-cells = <0>;
-			clock-frequency = <100000000>;
+		clock-frequency = <100000000>;
 	};
 
 	reg_can1_stby: regulator-can1-stby {

arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi

@@ -99,7 +99,6 @@
 
 		regulators {
 			buck1: BUCK1 {
-				regulator-compatible = "BUCK1";
 				regulator-min-microvolt = <600000>;
 				regulator-max-microvolt = <2187500>;
 				regulator-boot-on;
@@ -108,7 +107,6 @@
 			};
 
 			buck2: BUCK2 {
-				regulator-compatible = "BUCK2";
 				regulator-min-microvolt = <600000>;
 				regulator-max-microvolt = <2187500>;
 				regulator-boot-on;
@@ -119,7 +117,6 @@
 			};
 
 			buck4: BUCK4 {
-				regulator-compatible = "BUCK4";
 				regulator-min-microvolt = <600000>;
 				regulator-max-microvolt = <3400000>;
 				regulator-boot-on;
@@ -127,7 +124,6 @@
 			};
 
 			buck5: BUCK5 {
-				regulator-compatible = "BUCK5";
 				regulator-min-microvolt = <600000>;
 				regulator-max-microvolt = <3400000>;
 				regulator-boot-on;
@@ -135,7 +131,6 @@
 			};
 
 			buck6: BUCK6 {
-				regulator-compatible = "BUCK6";
 				regulator-min-microvolt = <600000>;
 				regulator-max-microvolt = <3400000>;
 				regulator-boot-on;
@@ -143,7 +138,6 @@
 			};
 
 			ldo1: LDO1 {
-				regulator-compatible = "LDO1";
 				regulator-min-microvolt = <1600000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -151,7 +145,6 @@
 			};
 
 			ldo2: LDO2 {
-				regulator-compatible = "LDO2";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <1150000>;
 				regulator-boot-on;
@@ -159,7 +152,6 @@
 			};
 
 			ldo3: LDO3 {
-				regulator-compatible = "LDO3";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
@@ -167,13 +159,11 @@
 			};
 
 			ldo4: LDO4 {
-				regulator-compatible = "LDO4";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo5: LDO5 {
-				regulator-compatible = "LDO5";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;

arch/arm64/boot/dts/freescale/imx8mp.dtsi

@@ -524,6 +524,7 @@
 				compatible = "fsl,imx8mp-gpc";
 				reg = <0x303a0000 0x1000>;
 				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-controller;
 				#interrupt-cells = <3>;
 
@@ -590,7 +591,7 @@
 						reg = <IMX8MP_POWER_DOMAIN_MIPI_PHY2>;
 					};
 
-					pgc_hsiomix: power-domains@17 {
+					pgc_hsiomix: power-domain@17 {
 						#power-domain-cells = <0>;
 						reg = <IMX8MP_POWER_DOMAIN_HSIOMIX>;
 						clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
@@ -1297,7 +1298,7 @@
 			reg = <0x32f10100 0x8>,
 			      <0x381f0000 0x20>;
 			clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
-				 <&clk IMX8MP_CLK_USB_ROOT>;
+				 <&clk IMX8MP_CLK_USB_SUSP>;
 			clock-names = "hsio", "suspend";
 			interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
 			power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB>;
@@ -1310,9 +1311,9 @@
 			usb_dwc3_0: usb@38100000 {
 				compatible = "snps,dwc3";
 				reg = <0x38100000 0x10000>;
-				clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
+				clocks = <&clk IMX8MP_CLK_USB_ROOT>,
 					 <&clk IMX8MP_CLK_USB_CORE_REF>,
-					 <&clk IMX8MP_CLK_USB_ROOT>;
+					 <&clk IMX8MP_CLK_USB_SUSP>;
 				clock-names = "bus_early", "ref", "suspend";
 				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&usb3_phy0>, <&usb3_phy0>;
@@ -1339,7 +1340,7 @@
 			reg = <0x32f10108 0x8>,
 			      <0x382f0000 0x20>;
 			clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
-				 <&clk IMX8MP_CLK_USB_ROOT>;
+				 <&clk IMX8MP_CLK_USB_SUSP>;
 			clock-names = "hsio", "suspend";
 			interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
 			power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB>;
@@ -1352,9 +1353,9 @@
 			usb_dwc3_1: usb@38200000 {
 				compatible = "snps,dwc3";
 				reg = <0x38200000 0x10000>;
-				clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
+				clocks = <&clk IMX8MP_CLK_USB_ROOT>,
 					 <&clk IMX8MP_CLK_USB_CORE_REF>,
-					 <&clk IMX8MP_CLK_USB_ROOT>;
+					 <&clk IMX8MP_CLK_USB_SUSP>;
 				clock-names = "bus_early", "ref", "suspend";
 				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&usb3_phy1>, <&usb3_phy1>;

arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts

@@ -133,7 +133,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	i2cmux@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2c1_pca9546>;
@@ -216,7 +216,7 @@
 	pinctrl-0 = <&pinctrl_i2c4>;
 	status = "okay";
 
-	pca9546: i2cmux@70 {
+	pca9546: i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;

arch/arm64/boot/dts/freescale/imx8mq-thor96.dts

@@ -339,7 +339,7 @@
 	bus-width = <4>;
 	non-removable;
 	no-sd;
-	no-emmc;
+	no-mmc;
 	status = "okay";
 
 	brcmf: wifi@1 {
@@ -359,7 +359,7 @@
 	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
 	bus-width = <4>;
 	no-sdio;
-	no-emmc;
+	no-mmc;
 	disable-wp;
 	status = "okay";
 };

arch/arm64/boot/dts/freescale/imx8qxp-mek.dts

@@ -61,7 +61,7 @@
 	pinctrl-0 = <&pinctrl_lpi2c1 &pinctrl_ioexp_rst>;
 	status = "okay";
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9646", "nxp,pca9546";
 		#address-cells = <1>;
 		#size-cells = <0>;

arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts

@@ -74,7 +74,7 @@
 
 	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
-			MX93_PAD_SD1_CLK__USDHC1_CLK		0x17fe
+			MX93_PAD_SD1_CLK__USDHC1_CLK		0x15fe
 			MX93_PAD_SD1_CMD__USDHC1_CMD		0x13fe
 			MX93_PAD_SD1_DATA0__USDHC1_DATA0	0x13fe
 			MX93_PAD_SD1_DATA1__USDHC1_DATA1	0x13fe
@@ -84,7 +84,7 @@
 			MX93_PAD_SD1_DATA5__USDHC1_DATA5	0x13fe
 			MX93_PAD_SD1_DATA6__USDHC1_DATA6	0x13fe
 			MX93_PAD_SD1_DATA7__USDHC1_DATA7	0x13fe
-			MX93_PAD_SD1_STROBE__USDHC1_STROBE	0x17fe
+			MX93_PAD_SD1_STROBE__USDHC1_STROBE	0x15fe
 		>;
 	};
 
@@ -102,7 +102,7 @@
 
 	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
-			MX93_PAD_SD2_CLK__USDHC2_CLK		0x17fe
+			MX93_PAD_SD2_CLK__USDHC2_CLK		0x15fe
 			MX93_PAD_SD2_CMD__USDHC2_CMD		0x13fe
 			MX93_PAD_SD2_DATA0__USDHC2_DATA0	0x13fe
 			MX93_PAD_SD2_DATA1__USDHC2_DATA1	0x13fe

arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi

@@ -98,7 +98,7 @@
 
 			uart1: serial@12100 {
 				compatible = "snps,dw-apb-uart";
-				reg = <0x11000 0x100>;
+				reg = <0x12100 0x100>;
 				reg-shift = <2>;
 				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
 				reg-io-width = <1>;

arch/arm64/boot/dts/qcom/msm8992-lg-bullhead.dtsi

@@ -3,6 +3,7 @@
  * Copyright (c) 2015, LGE Inc. All rights reserved.
  * Copyright (c) 2016, The Linux Foundation. All rights reserved.
  * Copyright (c) 2021, Petr Vorel <petr.vorel@gmail.com>
+ * Copyright (c) 2022, Dominik Kobinski <dominikkobinski314@gmail.com>
  */
 
 /dts-v1/;
@@ -51,6 +52,11 @@
 			reg = <0 0x03400000 0 0x1200000>;
 			no-map;
 		};
+
+		removed_region: reserved@5000000 {
+			reg = <0 0x05000000 0 0x2200000>;
+			no-map;
+		};
 	};
 };
 

arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts

@@ -11,6 +11,12 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/gpio-keys.h>
 
+/delete-node/ &adsp_mem;
+/delete-node/ &audio_mem;
+/delete-node/ &mpss_mem;
+/delete-node/ &peripheral_region;
+/delete-node/ &rmtfs_mem;
+
 / {
 	model = "Xiaomi Mi 4C";
 	compatible = "xiaomi,libra", "qcom,msm8992";
@@ -70,25 +76,67 @@
 		#size-cells = <2>;
 		ranges;
 
-		/* This is for getting crash logs using Android downstream kernels */
+		memory_hole: hole@6400000 {
+			reg = <0 0x06400000 0 0x600000>;
+			no-map;
+		};
+
+		memory_hole2: hole2@6c00000 {
+			reg = <0 0x06c00000 0 0x2400000>;
+			no-map;
+		};
+
+		mpss_mem: mpss@9000000 {
+			reg = <0 0x09000000 0 0x5a00000>;
+			no-map;
+		};
+
+		tzapp: tzapp@ea00000 {
+			reg = <0 0x0ea00000 0 0x1900000>;
+			no-map;
+		};
+
+		mdm_rfsa_mem: mdm-rfsa@ca0b0000 {
+			reg = <0 0xca0b0000 0 0x10000>;
+			no-map;
+		};
+
+		rmtfs_mem: rmtfs@ca100000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0 0xca100000 0 0x180000>;
+			no-map;
+
+			qcom,client-id = <1>;
+		};
+
+		audio_mem: audio@cb400000 {
+			reg = <0 0xcb000000 0 0x400000>;
+			no-mem;
+		};
+
+		qseecom_mem: qseecom@cb400000 {
+			reg = <0 0xcb400000 0 0x1c00000>;
+			no-mem;
+		};
+
+		adsp_rfsa_mem: adsp-rfsa@cd000000 {
+			reg = <0 0xcd000000 0 0x10000>;
+			no-map;
+		};
+
+		sensor_rfsa_mem: sensor-rfsa@cd010000 {
+			reg = <0 0xcd010000 0 0x10000>;
+			no-map;
+		};
+
 		ramoops@dfc00000 {
 			compatible = "ramoops";
-			reg = <0x0 0xdfc00000 0x0 0x40000>;
+			reg = <0 0xdfc00000 0 0x40000>;
 			console-size = <0x10000>;
 			record-size = <0x10000>;
 			ftrace-size = <0x10000>;
 			pmsg-size = <0x20000>;
 		};
-
-		modem_region: modem_region@9000000 {
-			reg = <0x0 0x9000000 0x0 0x5a00000>;
-			no-map;
-		};
-
-		tzapp: modem_region@ea00000 {
-			reg = <0x0 0xea00000 0x0 0x1900000>;
-			no-map;
-		};
 	};
 };
 
@@ -130,11 +178,6 @@
 	status = "okay";
 };
 
-&peripheral_region {
-	reg = <0x0 0x7400000 0x0 0x1c00000>;
-	no-map;
-};
-
 &pm8994_spmi_regulators {
 	VDD_APC0: s8 {
 		regulator-min-microvolt = <680000>;

arch/arm64/boot/dts/qcom/msm8992.dtsi

@@ -37,10 +37,6 @@
 	compatible = "qcom,rpmcc-msm8992", "qcom,rpmcc";
 };
 
-&tcsr_mutex {
-	compatible = "qcom,sfpb-mutex";
-};
-
 &timer {
 	interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,

arch/arm64/boot/dts/qcom/msm8994-huawei-angler-rev-101.dts

@@ -9,9 +9,6 @@
 
 #include "msm8994.dtsi"
 
-/* Angler's firmware does not report where the memory is allocated */
-/delete-node/ &cont_splash_mem;
-
 / {
 	model = "Huawei Nexus 6P";
 	compatible = "huawei,angler", "qcom,msm8994";
@@ -28,6 +25,22 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		tzapp_mem: tzapp@4800000 {
+			reg = <0 0x04800000 0 0x1900000>;
+			no-map;
+		};
+
+		removed_region: reserved@6300000 {
+			reg = <0 0x06300000 0 0xD00000>;
+			no-map;
+		};
+	};
 };
 
 &blsp1_uart2 {

arch/arm64/boot/dts/qcom/sc8280xp.dtsi

@@ -10,6 +10,7 @@
 #include <dt-bindings/interconnect/qcom,sc8280xp.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
+#include <dt-bindings/phy/phy-qcom-qmp.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
 #include <dt-bindings/thermal/thermal.h>
@@ -762,7 +763,7 @@
 				 <0>,
 				 <0>,
 				 <0>,
-				 <&usb_0_ssphy>,
+				 <&usb_0_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
 				 <0>,
 				 <0>,
 				 <0>,
@@ -770,7 +771,7 @@
 				 <0>,
 				 <0>,
 				 <0>,
-				 <&usb_1_ssphy>,
+				 <&usb_1_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
 				 <0>,
 				 <0>,
 				 <0>,
@@ -1673,42 +1674,26 @@
 			};
 		};
 
-		usb_0_qmpphy: phy-wrapper@88ec000 {
+		usb_0_qmpphy: phy@88eb000 {
 			compatible = "qcom,sc8280xp-qmp-usb43dp-phy";
-			reg = <0 0x088ec000 0 0x1e4>,
+			reg = <0 0x088eb000 0 0x4000>;
-			      <0 0x088eb000 0 0x40>,
-			      <0 0x088ed000 0 0x1c8>;
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges;
 
 			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
-				 <&rpmhcc RPMH_CXO_CLK>,
 				 <&gcc GCC_USB4_EUD_CLKREF_CLK>,
-				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
+				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
-			clock-names = "aux", "ref_clk_src", "ref", "com_aux";
+				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
-
+			clock-names = "aux", "ref", "com_aux", "usb3_pipe";
-			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
-				 <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
-			reset-names = "phy", "common";
 
 			power-domains = <&gcc USB30_PRIM_GDSC>;
 
-			status = "disabled";
+			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
+				 <&gcc GCC_USB4_DP_PHY_PRIM_BCR>;
+			reset-names = "phy", "common";
 
-			usb_0_ssphy: usb3-phy@88eb400 {
+			#clock-cells = <1>;
-				reg = <0 0x088eb400 0 0x100>,
+			#phy-cells = <1>;
-				      <0 0x088eb600 0 0x3ec>,
+
-				      <0 0x088ec400 0 0x364>,
+			status = "disabled";
-				      <0 0x088eba00 0 0x100>,
-				      <0 0x088ebc00 0 0x3ec>,
-				      <0 0x088ec200 0 0x18>;
-				#phy-cells = <0>;
-				#clock-cells = <0>;
-				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
-				clock-names = "pipe0";
-				clock-output-names = "usb0_phy_pipe_clk_src";
-			};
 		};
 
 		usb_1_hsphy: phy@8902000 {
@@ -1725,42 +1710,26 @@
 			status = "disabled";
 		};
 
-		usb_1_qmpphy: phy-wrapper@8904000 {
+		usb_1_qmpphy: phy@8903000 {
 			compatible = "qcom,sc8280xp-qmp-usb43dp-phy";
-			reg = <0 0x08904000 0 0x1e4>,
+			reg = <0 0x08903000 0 0x4000>;
-			      <0 0x08903000 0 0x40>,
-			      <0 0x08905000 0 0x1c8>;
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges;
 
 			clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
-				 <&rpmhcc RPMH_CXO_CLK>,
 				 <&gcc GCC_USB4_CLKREF_CLK>,
-				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
+				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>,
-			clock-names = "aux", "ref_clk_src", "ref", "com_aux";
+				 <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
+			clock-names = "aux", "ref", "com_aux", "usb3_pipe";
+
+			power-domains = <&gcc USB30_SEC_GDSC>;
 
 			resets = <&gcc GCC_USB3_PHY_SEC_BCR>,
 				 <&gcc GCC_USB4_1_DP_PHY_PRIM_BCR>;
 			reset-names = "phy", "common";
 
-			power-domains = <&gcc USB30_SEC_GDSC>;
+			#clock-cells = <1>;
+			#phy-cells = <1>;
 
 			status = "disabled";
-
-			usb_1_ssphy: usb3-phy@8903400 {
-				reg = <0 0x08903400 0 0x100>,
-				      <0 0x08903600 0 0x3ec>,
-				      <0 0x08904400 0 0x364>,
-				      <0 0x08903a00 0 0x100>,
-				      <0 0x08903c00 0 0x3ec>,
-				      <0 0x08904200 0 0x18>;
-				#phy-cells = <0>;
-				#clock-cells = <0>;
-				clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
-				clock-names = "pipe0";
-				clock-output-names = "usb1_phy_pipe_clk_src";
-			};
 		};
 
 		pmu@9091000 {
@@ -1910,7 +1879,7 @@
 				reg = <0 0x0a600000 0 0xcd00>;
 				interrupts = <GIC_SPI 803 IRQ_TYPE_LEVEL_HIGH>;
 				iommus = <&apps_smmu 0x820 0x0>;
-				phys = <&usb_0_hsphy>, <&usb_0_ssphy>;
+				phys = <&usb_0_hsphy>, <&usb_0_qmpphy QMP_USB43DP_USB3_PHY>;
 				phy-names = "usb2-phy", "usb3-phy";
 			};
 		};
@@ -1964,7 +1933,7 @@
 				reg = <0 0x0a800000 0 0xcd00>;
 				interrupts = <GIC_SPI 810 IRQ_TYPE_LEVEL_HIGH>;
 				iommus = <&apps_smmu 0x860 0x0>;
-				phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+				phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>;
 				phy-names = "usb2-phy", "usb3-phy";
 			};
 		};

arch/arm64/boot/dts/qcom/sm8250.dtsi

@@ -334,7 +334,6 @@
 				exit-latency-us = <6562>;
 				min-residency-us = <9987>;
 				local-timer-stop;
-				status = "disabled";
 			};
 		};
 	};

arch/arm64/boot/dts/qcom/sm8350.dtsi

@@ -2382,8 +2382,8 @@
 				 <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "iface", "core", "xo";
 			resets = <&gcc GCC_SDCC2_BCR>;
-			interconnects = <&aggre2_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>,
+			interconnects = <&aggre2_noc MASTER_SDCC_2 &mc_virt SLAVE_EBI1>,
-					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDCC_2 0>;
+					<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_SDCC_2>;
 			interconnect-names = "sdhc-ddr","cpu-sdhc";
 			iommus = <&apps_smmu 0x4a0 0x0>;
 			power-domains = <&rpmhpd SM8350_CX>;

arch/riscv/boot/dts/sifive/fu740-c000.dtsi

@@ -328,7 +328,7 @@
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000  0x0 0x60080000  0x0 0x60080000 0x0 0x10000>,      /* I/O */
 				 <0x82000000  0x0 0x60090000  0x0 0x60090000 0x0 0xff70000>,    /* mem */
-				 <0x82000000  0x0 0x70000000  0x0 0x70000000 0x0 0x1000000>,    /* mem */
+				 <0x82000000  0x0 0x70000000  0x0 0x70000000 0x0 0x10000000>,    /* mem */
 				 <0xc3000000 0x20 0x00000000 0x20 0x00000000 0x20 0x00000000>;  /* mem prefetchable */
 			num-lanes = <0x8>;
 			interrupts = <56>, <57>, <58>, <59>, <60>, <61>, <62>, <63>, <64>;

drivers/firmware/arm_scmi/driver.c

@@ -910,6 +910,8 @@ static int do_xfer(const struct scmi_protocol_handle *ph,
 			      xfer->hdr.protocol_id, xfer->hdr.seq,
 			      xfer->hdr.poll_completion);
 
+	/* Clear any stale status */
+	xfer->hdr.status = SCMI_SUCCESS;
 	xfer->state = SCMI_XFER_SENT_OK;
 	/*
 	 * Even though spinlocking is not needed here since no race is possible

drivers/firmware/arm_scmi/shmem.c

@@ -81,10 +81,11 @@ u32 shmem_read_header(struct scmi_shared_mem __iomem *shmem)
 void shmem_fetch_response(struct scmi_shared_mem __iomem *shmem,
 			  struct scmi_xfer *xfer)
 {
+	size_t len = ioread32(&shmem->length);
+
 	xfer->hdr.status = ioread32(shmem->msg_payload);
 	/* Skip the length of header and status in shmem area i.e 8 bytes */
-	xfer->rx.len = min_t(size_t, xfer->rx.len,
+	xfer->rx.len = min_t(size_t, xfer->rx.len, len > 8 ? len - 8 : 0);
-			     ioread32(&shmem->length) - 8);
 
 	/* Take a copy to the rx buffer.. */
 	memcpy_fromio(xfer->rx.buf, shmem->msg_payload + 4, xfer->rx.len);
@@ -93,8 +94,10 @@ void shmem_fetch_response(struct scmi_shared_mem __iomem *shmem,
 void shmem_fetch_notification(struct scmi_shared_mem __iomem *shmem,
 			      size_t max_len, struct scmi_xfer *xfer)
 {
+	size_t len = ioread32(&shmem->length);
+
 	/* Skip only the length of header in shmem area i.e 4 bytes */
-	xfer->rx.len = min_t(size_t, max_len, ioread32(&shmem->length) - 4);
+	xfer->rx.len = min_t(size_t, max_len, len > 4 ? len - 4 : 0);
 
 	/* Take a copy to the rx buffer.. */
 	memcpy_fromio(xfer->rx.buf, shmem->msg_payload, xfer->rx.len);

drivers/firmware/arm_scmi/virtio.c

@@ -160,7 +160,6 @@ static void scmi_vio_channel_cleanup_sync(struct scmi_vio_channel *vioch)
 	}
 
 	vioch->shutdown_done = &vioch_shutdown_done;
-	virtio_break_device(vioch->vqueue->vdev);
 	if (!vioch->is_rx && vioch->deferred_tx_wq)
 		/* Cannot be kicked anymore after this...*/
 		vioch->deferred_tx_wq = NULL;
@@ -482,6 +481,12 @@ static int virtio_chan_free(int id, void *p, void *data)
 	struct scmi_chan_info *cinfo = p;
 	struct scmi_vio_channel *vioch = cinfo->transport_info;
 
+	/*
+	 * Break device to inhibit further traffic flowing while shutting down
+	 * the channels: doing it later holding vioch->lock creates unsafe
+	 * locking dependency chains as reported by LOCKDEP.
+	 */
+	virtio_break_device(vioch->vqueue->vdev);
 	scmi_vio_channel_cleanup_sync(vioch);
 
 	scmi_free_channel(cinfo, data, id);

drivers/memory/atmel-sdramc.c

@@ -47,19 +47,17 @@ static int atmel_ramc_probe(struct platform_device *pdev)
 	caps = of_device_get_match_data(&pdev->dev);
 
 	if (caps->has_ddrck) {
-		clk = devm_clk_get(&pdev->dev, "ddrck");
+		clk = devm_clk_get_enabled(&pdev->dev, "ddrck");
 		if (IS_ERR(clk))
 			return PTR_ERR(clk);
-		clk_prepare_enable(clk);
 	}
 
 	if (caps->has_mpddr_clk) {
-		clk = devm_clk_get(&pdev->dev, "mpddr");
+		clk = devm_clk_get_enabled(&pdev->dev, "mpddr");
 		if (IS_ERR(clk)) {
 			pr_err("AT91 RAMC: couldn't get mpddr clock\n");
 			return PTR_ERR(clk);
 		}
-		clk_prepare_enable(clk);
 	}
 
 	return 0;

drivers/memory/mvebu-devbus.c

@@ -280,10 +280,9 @@ static int mvebu_devbus_probe(struct platform_device *pdev)
 	if (IS_ERR(devbus->base))
 		return PTR_ERR(devbus->base);
 
-	clk = devm_clk_get(&pdev->dev, NULL);
+	clk = devm_clk_get_enabled(&pdev->dev, NULL);
 	if (IS_ERR(clk))
 		return PTR_ERR(clk);
-	clk_prepare_enable(clk);
 
 	/*
 	 * Obtain clock period in picoseconds,

drivers/memory/omap-gpmc.c

@@ -1918,7 +1918,8 @@ int gpmc_cs_program_settings(int cs, struct gpmc_settings *p)
 		}
 	}
 
-	if (p->wait_pin > gpmc_nr_waitpins) {
+	if (p->wait_pin != GPMC_WAITPIN_INVALID &&
+	    p->wait_pin > gpmc_nr_waitpins) {
 		pr_err("%s: invalid wait-pin (%d)\n", __func__, p->wait_pin);
 		return -EINVAL;
 	}

drivers/memory/tegra/tegra186.c

@@ -22,32 +22,6 @@
 #define MC_SID_STREAMID_SECURITY_WRITE_ACCESS_DISABLED BIT(16)
 #define MC_SID_STREAMID_SECURITY_OVERRIDE BIT(8)
 
-static void tegra186_mc_program_sid(struct tegra_mc *mc)
-{
-	unsigned int i;
-
-	for (i = 0; i < mc->soc->num_clients; i++) {
-		const struct tegra_mc_client *client = &mc->soc->clients[i];
-		u32 override, security;
-
-		override = readl(mc->regs + client->regs.sid.override);
-		security = readl(mc->regs + client->regs.sid.security);
-
-		dev_dbg(mc->dev, "client %s: override: %x security: %x\n",
-			client->name, override, security);
-
-		dev_dbg(mc->dev, "setting SID %u for %s\n", client->sid,
-			client->name);
-		writel(client->sid, mc->regs + client->regs.sid.override);
-
-		override = readl(mc->regs + client->regs.sid.override);
-		security = readl(mc->regs + client->regs.sid.security);
-
-		dev_dbg(mc->dev, "client %s: override: %x security: %x\n",
-			client->name, override, security);
-	}
-}
-
 static int tegra186_mc_probe(struct tegra_mc *mc)
 {
 	struct platform_device *pdev = to_platform_device(mc->dev);
@@ -85,8 +59,6 @@ populate:
 	if (err < 0)
 		return err;
 
-	tegra186_mc_program_sid(mc);
-
 	return 0;
 }
 
@@ -95,13 +67,6 @@ static void tegra186_mc_remove(struct tegra_mc *mc)
 	of_platform_depopulate(mc->dev);
 }
 
-static int tegra186_mc_resume(struct tegra_mc *mc)
-{
-	tegra186_mc_program_sid(mc);
-
-	return 0;
-}
-
 #if IS_ENABLED(CONFIG_IOMMU_API)
 static void tegra186_mc_client_sid_override(struct tegra_mc *mc,
 					    const struct tegra_mc_client *client,
@@ -173,7 +138,6 @@ static int tegra186_mc_probe_device(struct tegra_mc *mc, struct device *dev)
 const struct tegra_mc_ops tegra186_mc_ops = {
 	.probe = tegra186_mc_probe,
 	.remove = tegra186_mc_remove,
-	.resume = tegra186_mc_resume,
 	.probe_device = tegra186_mc_probe_device,
 	.handle_irq = tegra30_mc_handle_irq,
 };

drivers/reset/Kconfig

@@ -257,7 +257,7 @@ config RESET_SUNXI
 
 config RESET_TI_SCI
 	tristate "TI System Control Interface (TI-SCI) reset driver"
-	depends on TI_SCI_PROTOCOL || COMPILE_TEST
+	depends on TI_SCI_PROTOCOL || (COMPILE_TEST && TI_SCI_PROTOCOL=n)
 	help
 	  This enables the reset driver support over TI System Control Interface
 	  available on some new TI's SoCs. If you wish to use reset resources

drivers/reset/reset-uniphier-glue.c

@@ -47,7 +47,6 @@ static int uniphier_glue_reset_probe(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	struct uniphier_glue_reset_priv *priv;
 	struct resource *res;
-	resource_size_t size;
 	int i, ret;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
@@ -60,7 +59,6 @@ static int uniphier_glue_reset_probe(struct platform_device *pdev)
 		return -EINVAL;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	size = resource_size(res);
 	priv->rdata.membase = devm_ioremap_resource(dev, res);
 	if (IS_ERR(priv->rdata.membase))
 		return PTR_ERR(priv->rdata.membase);
@@ -96,7 +94,7 @@ static int uniphier_glue_reset_probe(struct platform_device *pdev)
 
 	spin_lock_init(&priv->rdata.lock);
 	priv->rdata.rcdev.owner = THIS_MODULE;
-	priv->rdata.rcdev.nr_resets = size * BITS_PER_BYTE;
+	priv->rdata.rcdev.nr_resets = resource_size(res) * BITS_PER_BYTE;
 	priv->rdata.rcdev.ops = &reset_simple_ops;
 	priv->rdata.rcdev.of_node = dev->of_node;
 	priv->rdata.active_low = true;

drivers/soc/imx/imx8mp-blk-ctrl.c

@@ -212,7 +212,7 @@ static void imx8mp_hdmi_blk_ctrl_power_on(struct imx8mp_blk_ctrl *bc,
 		break;
 	case IMX8MP_HDMIBLK_PD_LCDIF:
 		regmap_set_bits(bc->regmap, HDMI_RTX_CLK_CTL0,
-				BIT(7) | BIT(16) | BIT(17) | BIT(18) |
+				BIT(16) | BIT(17) | BIT(18) |
 				BIT(19) | BIT(20));
 		regmap_set_bits(bc->regmap, HDMI_RTX_CLK_CTL1, BIT(11));
 		regmap_set_bits(bc->regmap, HDMI_RTX_RESET_CTL0,
@@ -241,6 +241,7 @@ static void imx8mp_hdmi_blk_ctrl_power_on(struct imx8mp_blk_ctrl *bc,
 		regmap_set_bits(bc->regmap, HDMI_TX_CONTROL0, BIT(1));
 		break;
 	case IMX8MP_HDMIBLK_PD_HDMI_TX_PHY:
+		regmap_set_bits(bc->regmap, HDMI_RTX_CLK_CTL0, BIT(7));
 		regmap_set_bits(bc->regmap, HDMI_RTX_CLK_CTL1, BIT(22) | BIT(24));
 		regmap_set_bits(bc->regmap, HDMI_RTX_RESET_CTL0, BIT(12));
 		regmap_clear_bits(bc->regmap, HDMI_TX_CONTROL0, BIT(3));
@@ -270,7 +271,7 @@ static void imx8mp_hdmi_blk_ctrl_power_off(struct imx8mp_blk_ctrl *bc,
 				  BIT(4) | BIT(5) | BIT(6));
 		regmap_clear_bits(bc->regmap, HDMI_RTX_CLK_CTL1, BIT(11));
 		regmap_clear_bits(bc->regmap, HDMI_RTX_CLK_CTL0,
-				  BIT(7) | BIT(16) | BIT(17) | BIT(18) |
+				  BIT(16) | BIT(17) | BIT(18) |
 				  BIT(19) | BIT(20));
 		break;
 	case IMX8MP_HDMIBLK_PD_PAI:
@@ -298,6 +299,7 @@ static void imx8mp_hdmi_blk_ctrl_power_off(struct imx8mp_blk_ctrl *bc,
 	case IMX8MP_HDMIBLK_PD_HDMI_TX_PHY:
 		regmap_set_bits(bc->regmap, HDMI_TX_CONTROL0, BIT(3));
 		regmap_clear_bits(bc->regmap, HDMI_RTX_RESET_CTL0, BIT(12));
+		regmap_clear_bits(bc->regmap, HDMI_RTX_CLK_CTL0, BIT(7));
 		regmap_clear_bits(bc->regmap, HDMI_RTX_CLK_CTL1, BIT(22) | BIT(24));
 		break;
 	case IMX8MP_HDMIBLK_PD_HDCP:
@@ -590,7 +592,6 @@ static int imx8mp_blk_ctrl_probe(struct platform_device *pdev)
 			ret = PTR_ERR(domain->power_dev);
 			goto cleanup_pds;
 		}
-		dev_set_name(domain->power_dev, "%s", data->name);
 
 		domain->genpd.name = data->name;
 		domain->genpd.power_on = imx8mp_blk_ctrl_power_on;

drivers/soc/imx/soc-imx8m.c

@@ -66,8 +66,8 @@ static u32 __init imx8mq_soc_revision(void)
 	ocotp_base = of_iomap(np, 0);
 	WARN_ON(!ocotp_base);
 	clk = of_clk_get_by_name(np, NULL);
-	if (!clk) {
+	if (IS_ERR(clk)) {
-		WARN_ON(!clk);
+		WARN_ON(IS_ERR(clk));
 		return 0;
 	}
 

drivers/soc/qcom/apr.c

@@ -461,9 +461,10 @@ static int apr_add_device(struct device *dev, struct device_node *np,
 		goto out;
 	}
 
+	/* Protection domain is optional, it does not exist on older platforms */
 	ret = of_property_read_string_index(np, "qcom,protection-domain",
 					    1, &adev->service_path);
-	if (ret < 0) {
+	if (ret < 0 && ret != -EINVAL) {
 		dev_err(dev, "Failed to read second value of qcom,protection-domain\n");
 		goto out;
 	}

drivers/soc/qcom/cpr.c

@@ -1708,12 +1708,16 @@ static int cpr_probe(struct platform_device *pdev)
 
 	ret = of_genpd_add_provider_simple(dev->of_node, &drv->pd);
 	if (ret)
-		return ret;
+		goto err_remove_genpd;
 
 	platform_set_drvdata(pdev, drv);
 	cpr_debugfs_init(drv);
 
 	return 0;
+
+err_remove_genpd:
+	pm_genpd_remove(&drv->pd);
+	return ret;
 }
 
 static int cpr_remove(struct platform_device *pdev)

include/linux/firmware/xlnx-zynqmp.h

@@ -545,8 +545,8 @@ int zynqmp_pm_request_wake(const u32 node,
 			   const u64 address,
 			   const enum zynqmp_pm_request_ack ack);
 int zynqmp_pm_get_rpu_mode(u32 node_id, enum rpu_oper_mode *rpu_mode);
-int zynqmp_pm_set_rpu_mode(u32 node_id, u32 arg1);
+int zynqmp_pm_set_rpu_mode(u32 node_id, enum rpu_oper_mode rpu_mode);
-int zynqmp_pm_set_tcm_config(u32 node_id, u32 arg1);
+int zynqmp_pm_set_tcm_config(u32 node_id, enum rpu_tcm_comb tcm_mode);
 int zynqmp_pm_set_sd_config(u32 node, enum pm_sd_config_type config, u32 value);
 int zynqmp_pm_set_gem_config(u32 node, enum pm_gem_config_type config,
 			     u32 value);
@@ -845,12 +845,12 @@ static inline int zynqmp_pm_get_rpu_mode(u32 node_id, enum rpu_oper_mode *rpu_mo
 	return -ENODEV;
 }
 
-static inline int zynqmp_pm_set_rpu_mode(u32 node_id, u32 arg1)
+static inline int zynqmp_pm_set_rpu_mode(u32 node_id, enum rpu_oper_mode rpu_mode)
 {
 	return -ENODEV;
 }
 
-static inline int zynqmp_pm_set_tcm_config(u32 node_id, u32 arg1)
+static inline int zynqmp_pm_set_tcm_config(u32 node_id, enum rpu_tcm_comb tcm_mode)
 {
 	return -ENODEV;
 }

include/linux/soc/ti/omap1-io.h

@@ -5,7 +5,7 @@
 #ifndef __ASSEMBLER__
 #include <linux/types.h>
 
-#ifdef CONFIG_ARCH_OMAP1_ANY
+#ifdef CONFIG_ARCH_OMAP1
 /*
  * NOTE: Please use ioremap + __raw_read/write where possible instead of these
  */
@@ -15,7 +15,7 @@ extern u32 omap_readl(u32 pa);
 extern void omap_writeb(u8 v, u32 pa);
 extern void omap_writew(u16 v, u32 pa);
 extern void omap_writel(u32 v, u32 pa);
-#else
+#elif defined(CONFIG_COMPILE_TEST)
 static inline u8 omap_readb(u32 pa)  { return 0; }
 static inline u16 omap_readw(u32 pa) { return 0; }
 static inline u32 omap_readl(u32 pa) { return 0; }

include/soc/bcm2835/raspberrypi-firmware.h

@@ -170,7 +170,7 @@ struct rpi_firmware_clk_rate_request {
 
 #define RPI_FIRMWARE_CLK_RATE_REQUEST(_id)	\
 	{					\
-		.id = _id,			\
+		.id = cpu_to_le32(_id),		\
 	}
 
 #if IS_ENABLED(CONFIG_RASPBERRYPI_FIRMWARE)