mirror of
https://github.com/Ralim/IronOS.git
synced 2025-07-23 12:23:06 +02:00
a0a779faba
* Minor doc updates * pydoc * Draft tip selection menu * Start linking in manual tip resistance * Enable on Pinecilv1 / TS10x * Fixup drawing tip type * Update Settings.cpp * Rename JBC type * Add translations * Handle one tip type * Refactor header includes * Fixup translation_IT.json * Fixing up includes * Format * Apply suggestions from code review Co-authored-by: discip <53649486+discip@users.noreply.github.com> * Update Documentation/Hardware.md Co-authored-by: discip <53649486+discip@users.noreply.github.com> --------- Co-authored-by: = <=> Co-authored-by: discip <53649486+discip@users.noreply.github.com>
188 lines
8.0 KiB
C
188 lines
8.0 KiB
C
#ifndef CONFIGURATION_H_
|
|
#define CONFIGURATION_H_
|
|
#include <stdint.h>
|
|
/**
|
|
* Configuration.h
|
|
* Define here your default pre settings for Pinecilv2
|
|
*
|
|
*/
|
|
|
|
//===========================================================================
|
|
//============================= Default Settings ============================
|
|
//===========================================================================
|
|
/**
|
|
* Default soldering temp is 320.0 C
|
|
* Temperature the iron sleeps at - default 150.0 C
|
|
*/
|
|
|
|
#define SLEEP_TEMP 150 // Default sleep temperature
|
|
#define BOOST_TEMP 420 // Default boost temp.
|
|
#define BOOST_MODE_ENABLED 1 // 0: Disable 1: Enable
|
|
|
|
/**
|
|
* Blink the temperature on the cooling screen when its > 50C
|
|
*/
|
|
#define COOLING_TEMP_BLINK 0 // 0: Disable 1: Enable
|
|
|
|
/**
|
|
* How many seconds/minutes we wait until going to sleep/shutdown.
|
|
* Values -> SLEEP_TIME * 10; i.e. 5*10 = 50 Seconds!
|
|
*/
|
|
#define SLEEP_TIME 5 // x10 Seconds
|
|
#define SHUTDOWN_TIME 10 // Minutes
|
|
|
|
/**
|
|
* Auto start off for safety.
|
|
* Pissible values are:
|
|
* 0 - none
|
|
* 1 - Soldering Temperature
|
|
* 2 - Sleep Temperature
|
|
* 3 - Sleep Off Temperature
|
|
*/
|
|
#define AUTO_START_MODE 0 // Default to none
|
|
|
|
/**
|
|
* Locking Mode
|
|
* When in soldering mode a long press on both keys toggle the lock of the buttons
|
|
* Possible values are:
|
|
* 0 - Desactivated
|
|
* 1 - Lock except boost
|
|
* 2 - Full lock
|
|
*/
|
|
#define LOCKING_MODE 0 // Default to desactivated for safety
|
|
|
|
/**
|
|
* OLED Orientation
|
|
*
|
|
*/
|
|
#define ORIENTATION_MODE 2 // 0: Right 1:Left 2:Automatic - Default Automatic
|
|
#define MAX_ORIENTATION_MODE 2 // Up to auto
|
|
#define REVERSE_BUTTON_TEMP_CHANGE 0 // 0:Default 1:Reverse - Reverse the plus and minus button assigment for temperature change
|
|
|
|
/**
|
|
* OLED Brightness
|
|
*
|
|
*/
|
|
#define MIN_BRIGHTNESS 1 // Min OLED brightness selectable
|
|
#define MAX_BRIGHTNESS 101 // Max OLED brightness selectable
|
|
#define BRIGHTNESS_STEP 25 // OLED brightness increment
|
|
#define DEFAULT_BRIGHTNESS 26 // default OLED brightness
|
|
|
|
/**
|
|
* Temp change settings
|
|
*/
|
|
#define TEMP_CHANGE_SHORT_STEP 1 // Default temp change short step +1
|
|
#define TEMP_CHANGE_LONG_STEP 10 // Default temp change long step +10
|
|
#define TEMP_CHANGE_SHORT_STEP_MAX 50 // Temp change short step MAX value
|
|
#define TEMP_CHANGE_LONG_STEP_MAX 90 // Temp change long step MAX value
|
|
|
|
/* Power pulse for keeping power banks awake*/
|
|
|
|
#define POWER_PULSE_INCREMENT 1
|
|
#define POWER_PULSE_MAX 100 // x10 max watts
|
|
#define POWER_PULSE_WAIT_MAX 9 // 9*2.5s = 22.5 seconds
|
|
#define POWER_PULSE_DURATION_MAX 9 // 9*250ms = 2.25 seconds
|
|
|
|
#ifdef MODEL_Pinecilv2
|
|
#define POWER_PULSE_DEFAULT 0
|
|
#else
|
|
#define POWER_PULSE_DEFAULT 5
|
|
#endif /* Pinecil */
|
|
#define POWER_PULSE_WAIT_DEFAULT 4 // Default rate of the power pulse: 4*2500 = 10000 ms = 10 s
|
|
#define POWER_PULSE_DURATION_DEFAULT 1 // Default duration of the power pulse: 1*250 = 250 ms
|
|
|
|
/**
|
|
* OLED Orientation Sensitivity on Automatic mode!
|
|
* Motion Sensitivity <0=Off 1=Least Sensitive 9=Most Sensitive>
|
|
*/
|
|
#define SENSITIVITY 7 // Default 7
|
|
|
|
/**
|
|
* Detailed soldering screen
|
|
* Detailed idle screen (off for first time users)
|
|
*/
|
|
#define DETAILED_SOLDERING 0 // 0: Disable 1: Enable - Default 0
|
|
#define DETAILED_IDLE 0 // 0: Disable 1: Enable - Default 0
|
|
|
|
#define THERMAL_RUNAWAY_TIME_SEC 20
|
|
#define THERMAL_RUNAWAY_TEMP_C 20
|
|
|
|
#define CUT_OUT_SETTING 0 // default to no cut-off voltage
|
|
#define RECOM_VOL_CELL 33 // Minimum voltage per cell (Recommended 3.3V (33))
|
|
#define TEMPERATURE_INF 0 // default to 0
|
|
#define DESCRIPTION_SCROLL_SPEED 0 // 0: Slow 1: Fast - default to slow
|
|
#define ANIMATION_LOOP 1 // 0: off 1: on
|
|
#define ANIMATION_SPEED settingOffSpeed_t::MEDIUM
|
|
|
|
#define OP_AMP_Rf_Pinecil 680 * 1000 // 680 Kilo-ohms -> From schematic, R1
|
|
#define OP_AMP_Rin_Pinecil 2370 // 2.37 Kilo-ohms -> From schematic, R2
|
|
|
|
#define OP_AMP_GAIN_STAGE_PINECIL (1 + (OP_AMP_Rf_Pinecil / OP_AMP_Rin_Pinecil))
|
|
|
|
#if defined(MODEL_Pinecilv2) == 0
|
|
#error "No model defined!"
|
|
#endif
|
|
|
|
#ifdef MODEL_Pinecilv2
|
|
#define ADC_VDD_MV 3200 // ADC max reading millivolts
|
|
#define ADC_MAX_READING ((1 << 16) >> 1) // Maximum reading of the adc
|
|
#define SOLDERING_TEMP 320 // Default soldering temp is 320.0 °C
|
|
#define VOLTAGE_DIV 630 // 600 - Default divider from schematic
|
|
#define CALIBRATION_OFFSET 900 // 900 - Default adc offset in uV
|
|
#define MIN_CALIBRATION_OFFSET 100 // Min value for calibration
|
|
#define PID_POWER_LIMIT 120 // Sets the max pwm power limit
|
|
#define POWER_LIMIT 0 // 0 watts default limit
|
|
#define MAX_POWER_LIMIT 120 // Sets the max power limit
|
|
#define POWER_LIMIT_STEPS 5 //
|
|
#define OP_AMP_GAIN_STAGE OP_AMP_GAIN_STAGE_PINECIL // Uses TS100 resistors
|
|
#define TEMP_uV_LOOKUP_HAKKO // Use Hakko lookup table
|
|
#define USB_PD_VMAX 28 // Maximum voltage for PD to negotiate
|
|
#define PID_TIM_HZ (10) // Tick rate of the PID loop
|
|
#define MAX_TEMP_C 450 // Max soldering temp selectable °C
|
|
#define MAX_TEMP_F 850 // Max soldering temp selectable °F
|
|
#define MIN_TEMP_C 10 // Min soldering temp selectable °C
|
|
#define MIN_TEMP_F 50 // Min soldering temp selectable °F
|
|
#define MIN_BOOST_TEMP_C 250 // The min settable temp for boost mode °C
|
|
#define MIN_BOOST_TEMP_F 480 // The min settable temp for boost mode °F
|
|
#define DEVICE_HAS_VALIDATION_CODE // We have 2 digit validations
|
|
#define POW_PD 1 // Supported features
|
|
#define USB_PD_EPR_WATTAGE 140 // USB PD EPR Wattage
|
|
#define POW_PD_EXT 0 // Future-proof macro for other models with other PD modes
|
|
#define POW_QC 1 // Supported features
|
|
#define POW_DC 1 // Supported features
|
|
#define POW_QC_20V 1 // Supported features
|
|
#define POW_EPR 1
|
|
#define ENABLE_QC2 1
|
|
#define MAG_SLEEP_SUPPORT 1
|
|
#define AUTO_TIP_SELECTION 1 // Can auto-select the tip
|
|
#define TIPTYPE_T12 1 // Can manually pick a T12 tip
|
|
#define DEVICE_HAS_VALIDATION_SUPPORT
|
|
#define OLED_96x16 1
|
|
#define TEMP_NTC
|
|
#define ACCEL_BMA
|
|
#define CUSTOM_MAX_TEMP_C 1 // Uses custom max temp lookup
|
|
#define ACCEL_SC7
|
|
#define HALL_SENSOR
|
|
#define HALL_SI7210
|
|
#define DEBUG_UART_OUTPUT
|
|
#define HAS_POWER_DEBUG_MENU
|
|
#define HARDWARE_MAX_WATTAGE_X10 750
|
|
#define BLE_ENABLED // We have a BLE stack
|
|
#define NEEDS_VBUS_PROBE 0 // No vbus probe, its not connected in pcb
|
|
#define CANT_DIRECT_READ_SETTINGS // We cant memcpy settings due to flash cache
|
|
#define TIP_CONTROL_PID // We use PID rather than integrator
|
|
#define TIP_PID_KP 40 // Reasonable compromise for most tips so far
|
|
#define TIP_PID_KI 6 // About as high for stability across tips
|
|
#define TIP_PID_KD 200 // Helps dampen smaller tips; ~= nothing for larger tips
|
|
#define FILTER_DISPLAYED_TIP_TEMP 8 // Filtering for GUI display
|
|
|
|
#endif /* Pinecilv2 */
|
|
|
|
#define FLASH_PAGE_SIZE (1024) // Read pages
|
|
// Erase is 4 or 8 k size, so we pad these apart for now
|
|
// If we ever get low on flash, will need better solution
|
|
#define FLASH_LOGOADDR (0x23000000 + (1016 * FLASH_PAGE_SIZE))
|
|
#define SETTINGS_START_PAGE (1023 * FLASH_PAGE_SIZE) // Hal auto offsets base addr
|
|
|
|
#endif /* CONFIGURATION_H_ */
|